Bedienungsanleitung Honda UMK435E (Seite 5 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

478015

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

5 EN

When the machine is equipped with a grass-cutting disc, the disc

must be fitted with the stabilizer (see page 4).

Correct balancing is obtained when the stabilizer just gently touches

the ground [2].

It must be possible to raise the cutting attachment off the ground

with only a slight effort on the handles. If adjustment is required,

move the attachment point [4] forwards if the cutting attachment

feels too heavy or rearwards if it feels too light. Loosen the bolts with

the Torx wrench [3] supplied to move the harness attachment point

to the desired position.

CAUTION: (U type )

• Be careful not to pull the throttle cable too tight when moving

the handle [5]. Check that the throttle trigger operates

smoothly.

Adjust the position of the loop handle or the bike handle [5] by

loosening the four bolts to obtain a comfortable operating position.

When you have found the ideal position, check the balance again

and adjust if necessary.

Then securely tighten the bolts to lock the handle in position.

For reference, the standard adjustments are as follows for the

specified types of brushcutter:

FILLING THE FUEL TANK

The pressure inside fuel

tanks may increase when

the ambient temperature

rises. The cap should be

removed with care to avoid

any splashing of fuel. Fuel

should be stored in a cool

place, for short periods of

time, and must never be

left in direct sunlight.

CAUTION:

• Clean the fuel tank cap and its edges to prevent foreign bodies

from entering the tank.

• Fill the fuel tank with a suitable funnel or a jerrycan with a suitable

spout.

• For easy filling, place the machine in the operating position.

• Make sure that the machine remains in a stable position

throughout this operation so that it does not fall over.

Petrol is extremely flammable and, in some circumstances, it

is explosive.

Fill the fuel tank in a well ventilated area with the engine

switched off.

Do not smoke and avoid any flames or sparks in the area where

filling is performed and where the fuel is stored.

Do not overfill the fuel tank. (The fuel level must be below the

filler neck).

After filling the tank, make sure that the tank cap is correctly

fitted.

Take care not to spill fuel during the tank filling operation.

Petrol splashes or vapours could catch fire.

Make sure that any spilled petrol has evaporated and that

vapours have dispersed before starting the engine.

Avoid direct contact of petrol with the skin and do not breathe

the vapours.

KEEP FUEL OUT OF REACH OF CHILDREN.

UMK425E1 UMK435E1

L type

[6] 530 mm 545 mm

[7] 760 mm 775 mm

[2]

[5]

[3]

[4]

[3]

[4]

[5]

[3]

[7]

[6]

UMK425E1 UMK435E1

U type

[8] 490 mm 500 mm

[9] 740 mm 750 mm

UMK425E1 UMK435E1

Tank capacity 0.58 l (580 cc) 0.63 l (630 cc)

Recommended fuel Premium unleaded

[9]

[8]

B3 C12

SAFETY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honda UMK435E Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honda UMK435E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info