Bedienungsanleitung Honeywell airconditioner amh 12000e (Seite 6 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

367938

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

the lugs on the exhaust nozzle connector are engaged with the

grooves on the connector of unit (Fig. 2).

3. Attach the exhaust nozzle (9) to the exhaust nozzle connector (10).

4. Extend the exhaust hose (11) and close the window as far as

possible trapping the exhaust nozzle (9)

INSTALLATION INSTRUCTIONS

Air Conditioning with Installation

If required your appliance can also be installed semi-permanently

(Fig. 5).

Proceed as follows:

1. Drill a hole in an outside wall, through a door or a window pane.

The hole should be no larger than 125mm, and between 35cm and

100cm from floor level. If you drill through a wall, we recommend

that you insulate that section with suitable materials. (Figs. 6-7)

2. Fit the flange accessory fixture (12) provided into the hole.

3. Fit the exhaust hose in the housing at the back of the appliance

(Fig. 2).

4. Insert the other end of the exhaust hose to the flange already

placed in the hole (Fig. 7).

NOTE: When installing the air conditioner semi-permanently, you

should leave a door slightly open (as little as 1cm) to guarantee

sufficient ventilation.

OPEREATING INSTRUCTIONS: CONTROL PANEL

Power Control

The power control turns the unit on and off.

Warning Light

Condensed water may accumulate in the unit. If the internal tank

becomes full, the warning light in the LCD Display will light up and

the unit will not operate until the unit has been drained.

Mode Control

The Mode Control has 3 settings: Cool, Dehumidify, and Fan. The

settings are adjusted with the Mode Control button. A light will

indicate which setting is being used.

1. Cooling Mode

When cool mode is selected, “

” will show in the LCD display.

During the cooling mode the air is cooled and hot air is exhausted

to the outside air through the exhaust tube. Adjust fan speed and

temperature to suit your desired comfort level.

Note : The air exchange hoses must vent outside the room when

using Cooling Mode.

2. Dehumidify Mode

When dehumidify mode is selected, “

” will show in the LCD

display. Air is dehumidified as it passes through the air conditioner

without being in full cooling mode. If the room temperature is

>25°C (77°F), fan speed can be adjusted; otherwise, fan speed is

set at Medium.

Note : The warm air exchange hoses must vent inside the

room when using Dehumidify Mode, not outside as it does

when cooling. If the unit is vented outside some cooling

will occur.

3. Fan Mode

When fan mode is selected,

, or will be shown in the LCD

display. Air is circulated throughout the room with no cooling.

Note: Unit does not need to be vented in Fan Mode.

Fan Speed Control

The Fan Speed Control has 3 settings:

High;

Medium; and Low.

Time Setting

Auto Shut Off: With machine in running mode, press the timer

button. Press “+” or “-” to select number of hours you would like

the unit to run before it automatically shuts off.

Auto Turn On: With machine in stand-by mode, press the timer

button. Press “+” or “-” to select number of hours before the unit

automatically starts running in air conditioning mode.

NOTE: Time is adjustable between 1-24 hours.

Temperature Controls

• The temperature control buttons are used for adjusting the

thermostat.

• The default LCD display is the room temperature.

• In cooling mode, when “+” or “-” is pressed the set temperature

is displayed and may be adjusted. After 15 seconds the display will

revert back to showing the room temperature. Temperature is only

adjustable in cool mode.

NOTE: By pressing both the “+” and “-” buttons at the

same time for more than 3 seconds, the display will toggle

between Celsius and Fahrenheit.

OPERATING INSTRUCTIONS: REMOTE Control

The functions work the same a your air conditioner’s control panel.

All key functions can be accessed from the remote control (Fig. 10).

Power Control: On/Off

Fan Speed Control:

High;

Medium; Low

On/Off Timer Control:

In running mode: Auto switch off

In stand-by mode: Auto switch off

Press “

” or “ ” button to adjust the time setting in 1 hour

intervals.

Fahrenheit/Celsius Button: toggles between Celsius and

Fahrenheit settings.

LCD Display

Time/Temperature Set Control:

• Used for adjusting the timer and temperature.

• The default display on the control panel is room

temperature

• When “

” or “ ” button is pressed in cool mode the set

temperature is displayed and may be adjusted. After 15 seconds

the display will revert back to room temperature.

• Timer setting is available from 1-24 hours by pressing the “

” or

“ ”button.” button.

Mode Control: Press to change the operating mode, which will

rotate through Cool - Dehumidify - Fan and back to Cool.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell airconditioner amh 12000e Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info