Bedienungsanleitung Honeywell chronotherm 4 T8602A (Seite 2 von 12) (Englisch)

6417

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

69-0309—9 2

T8602A,B,C,D AND TS8602A,C Chronotherm

III FUEL SAVER THERMOSTATS

CAUTION

Disconnect power supply to prevent electrical

shock or equipment damage.

Location

Install thermostat and wallplate about 5 ft (1.5m) above the

floor in an area with good air circulation at room

temperature.

Do not install the thermostat where it can be affected by:

— drafts or dead spots behind doors, in corners, or

under cabinets.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall,

behind the thermostat.

If Replacing An Existing Thermostat

Turn off power to the thermostat at the furnace or boiler. A

two-transformer system can require turning off two

switches or disconnects. Remove any existing wallplate or

subbase from the wall. Write down the letter or number on

each wiring terminal, as the wire is removed, to avoid

miswiring later.

If New Installation

Run cable to the hole in the selected wall location, and pull

about 3 in. (76 mm) of wire through the opening. Color-

coded, 18 gauge thermostat cable with at least one

conductor for each wiring terminal is recommended.

Push excess wire back into the hole, and plug the hole

with nonhardening caulk, putty or insulation to prevent

drafts from affecting the thermostat operation.

Mounting Wallplate

Remove thermostat from wallplate. See Fig. 1.

The wallplate does not require leveling for operation, but

for appearance only. The wallplate mounts directly onto

the wall with the screws included. Using the wallplate as a

template, with a pencil, mark two (of three) mounting

screw positions on the wallplate that fit the application. See

Fig. 2. Use a 3/16 in. bit to drill holes for the anchors.

Gently tap anchors into the holes until flush with the wall

surface. Thread wires through the center opening of the

wallplate. Mount the wallplate using the two screws

provided. Gently tighten the screws, level the top surface

of the wallplate, and then securely tighten the screws.

WIRES THROUGH

WALL OPENING

WALL

ANCHORS

(2)

WALLPLATE

MOUNTING

HOLES (3)

MOUNTING

SCREWS (2)

USE TWO MOUNTING HOLES THAT

BEST FIT APPLICATION.

M2917

M2918

Fig. 1. Removing thermostat from wallplate.

Fig. 2. Mounting wallplate on wall.

Wiring

CAUTION

The TS8602A,C can only be used on 750 mV

heating applications. The TS8602A,C will not

function properly on 250 mV, 500 mV or 24 Vac

heating applications.

All wiring must comply with local electrical codes and

ordinances.

Disconnect power before wiring to prevent electrical shock

or equipment damage.

The shape of the terminal barrier permits insertion of

straight or conventional wraparound wiring connections.

Either method is acceptable.

Refer to Fig. 4 through 15 for typical wallplate and

thermostat hookups.

NOTE: • Keep all wiring restricted to the ribbed area

surrounding the terminals (Fig. 3) to assure

thermostat/wallplate contact.

• For single transformer applications, jumper

terminals R and RC for proper operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell chronotherm 4 T8602A Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell chronotherm 4 T8602A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info