Bedienungsanleitung Honeywell chronotherm 4 T8602A (Seite 7 von 12) (Englisch)

6417

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

69-0309—97

T8602A,B,C,D AND TS8602A,C Chronotherm

III FUEL SAVER THERMOSTATS

With Adaptive Intelligent Recovery™, the room will reach

the comfort temperature at the exact time programmed

into the thermostat. The control temperature will increase

gradually, and turn the equipment on and off several times

to reach the comfort temperature slowly and on time.

There will be no wasted of energy associated with rapid

temperature changes and temperature overshoot.

With conventional recovery, the start time should be

programmed to be earlier than the desired comfort time. It

may require some trial and error to arrive at the best

starting time.

Setting Time/Temperature (Some Models)

The display readout may be converted between a 12 and

24 hour clock or °C and °F using screws 2A and 2B as

indicated in Fig. 16.

Setting Fan Operation

Some T8602C models include a fan operation switch on

the back of the thermostat on the lower left corner. See

Fig. 15. See Table 2 to determine correct setting of fan

operation switch.

CAUTION

The fan operation switch, which is available on

some T8602C models, is factory set to the NON

ELEC. position. If the system requires direct

thermostat control of the fan in heat mode, the

switch must be set to the ELEC. position. See

Table 2.

Table 2. T8602C Fan Operation Switch Setting.

Installing Batteries

Power is supplied for the thermostat by three AA alkaline

batteries. Batteries are included with thermostat. Install

batteries in back of thermostat as shown in Fig. 17. The

display will flash 1:00 PM and room temperature.

When the batteries are going dead, the display will flash

REPL BAT. If device has system switch, set to OFF.

Remove the thermostat from the wall and install three new

AA alkaline batteries. We recommend Energizer®

batteries. Change batteries within approximately 30

seconds from the time the batteries are removed to

prevent program loss and the necessity to reprogram.

IMPORTANT

The low battery warning will be displayed about

two months before the batteries are dead. When

the batteries are dead, the system will shut down.

After batteries are replaced, thermostat will

require reprogramming.

Mounting The Thermostat

Hang the thermostat on the tabs at the top of the base.

See Fig. 18A. Swing down and press on the lower edge

until the thermostat snaps into place. See Fig. 18B. Open

the cover, and tighten the captive mounting screws. See

Fig. 18C.

Setting Day and Time

Set the present day and time. When the thermostat is first

turned on, the display will read 1:00 PM and the room

temperature. It will go off for only a few seconds, then

begin to flash on and off.

Press .

Press TIME or to set the current

time.

Press .

Press to set the current day. Each press of the

DAY key advances the display one day.

If the display will not come on:

• Check mounting of thermostat to wallplate. If loose or

misaligned, remove thermostat and reinstall on the

wallplate, making sure it is firmly attached.

• Check to see that all the batteries are good and

installed correctly.

SET

PRESENT

DAY/TIME

AHEAD

Fan Operation

Switch Setting

(4A) Comments

Fan controlled

directly by

thermostat in heat

mode (typically

electric furnaces).

Set to ELEC.

position.

Use only one

system

transformer

jumper R and

RC.

Fan has

independent

control in heat

mode (typically

gas, oil, millivolt

and some electric

furnaces).

Set to NON

ELEC. position

System may

have one or two

transformers;

if one

transformer,

jumper R and

RC.

SET

PRESENT

DAY/TIME

DAY

BACK

M2083

BATTERY

PLACEMENT

(NOTE CORRECT PLUS

AND MINUS DIRECTION)

Fig. 17. Battery placement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell chronotherm 4 T8602A Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell chronotherm 4 T8602A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info