Bedienungsanleitung Honeywell CT3600 (Seite 6 von 24) (Englisch)

32399

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

69-1642 6

STEP 2. REMOVE OLD THERMOSTAT

❑ Test your heating and cooling systems to make sure they work properly. If either system does not work, contact

your local heating/air-conditioning dealer. To avoid compressor damage, do not operate the cooling system when

outdoor temperature is below 50°F (10°C).

❑ Turn off power to the system at the furnace or the fuse/circuit breaker panel.

❑ Carefully unpack your new thermostat and wallplate. Save package of screws, instructions, and receipt.

❑ Remove the cover from the old thermostat. If the cover does not snap off when pulled firmly from the bottom, check

for a screw or screws used to lock on the cover.

❑ Loosen the screw or screws holding the thermostat to the wallplate and lift the thermostat away.

❑ Disconnect the wires from the old thermostat. As you disconnect each wire, attach the enclosed labels with the old

terminal designation. If there are only two wires, they do not need to be labeled. Wrap the wires around a pencil as

shown to keep them from falling back into the wall.

Special Installations

Read this section if you are replacing:

• Clock thermostat with separate wires for the clock.

• Thermostat with six or more wires connected to it.

• Thermostat in a heating only system with three wires.

Replacing a Clock Thermostat that has C or C1 Clock Terminals

If you are replacing a Honeywell Chronotherm®

Thermostat, you may find one or two

wires going to the C or C1 clock terminals on the Chronotherm wiring wallplate. Do not allow them to touch, or you can

damage the transformer. Disconnect the wires and wrap them separately using electrical tape. Do not wrap them

together. Place the wires where they will not interfere with the operation of the new thermostat. Record the colors and

terminal designation labels of the remaining wires.

Replacing a Thermostat that has Six or More Wires

If there are six or more wires (excluding clock wires attached to terminals), you probably have a variation of a

multistage heat pump or other multistage system. This thermostat is not compatible with multistage systems, so return

the product to the place of purchase. For information about which programmable thermostats will work with your

system, call Honeywell Customer Relations Center, at 1-800-468-1502.

Replacing a Thermostat that has Three Wires

If you have three wires for a heating only system and can operate the fan using the fan ON switch this thermostat

works with your system. However, some hot water (zoned) heating systems also have three wires. Your thermostat will

work only if you install an isolating relay on these systems. For details, call your local heating and/or cooling contractor.

WIRES THROUG

WALL OPENING

M5136

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell CT3600 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell CT3600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info