Bedienungsanleitung Honeywell DYF012 Series (Seite 3 von 14) (Englisch, Französisch, Spanisch)

723857

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

4 5

HYF013 SERIES OPERATION INSTRUCTIONS

• Place the fan on a level and dry surface.

• Plug the power cord into a polarized 120 Volt AC wall outlet.

• To operate, turn knob and select appropriate fan speed:

High ( ) Medium ( ), or Low ( ) (Fig. 13).

• To activate or disengage the fan oscillation, press the oscillation

button. (

) (Fig. 14).

• Operate the automatic shut-off timer feature by turning the timer

knob to the desired setting of 10 to 120 minutes (Fig. 15).

• To turn on the fan after automatic shut-off, turn the knob

counterclockwise

to the ON position

•

To turn the fan Off, turn

knob to the Off position.

( )

HYF023 SERIES OPERATION INSTRUCTIONS

• Place the fan on a level and dry surface.

• Plug the power cord into a polarized 120 Volt AC wall outlet.

• To turn the fan on, press the Power button (

) located on

the left side of the control panel.

• To select fan speed, press Speed Control button (

) until

the desired speed is selected:

High (

), Medium ( ), or Low ( ) (Fig. 16).

• To activate or disengage the fan oscillation, press the

oscillation button (

). Press the Oscillation button again to

turn the Oscillation feature off (Fig. 17).

Fig. 16

Fig. 17

NOTE: Remove all contents from the box being careful not to discard the manual and hardware needed

for assembly. A phillips head screw driver (

) is required for assembly and is not included with the

fan purchase.

A. Pedestal Assembly

• Place the power cord through the center of the front and rear

pedestal assemblies with the screw hole openings facing

towards the fan.

• Align the front and rear pedestal assembly and firmly snap

together (Fig. 7).

B. Securing the Tower Fan to the Pedestal

• Gently turn fan upside down.

• Line up the 3 screw holes on the pedestal with the 3 screw

holes on the bottom of the fan housing. Use the 3 (M5 x 12)

screws included in the box and a phillips head screw driver

(

) to secure the pedestal to the fan housing (Fig. 8).

C. Base Assembly

• With the fan in the upside down position, pass the power cord

through the recessed slot located in the center of the rear base

assembly (Fig. 9).

• Align the rear and front base assembly and firmly snap together

by pushing the 4 round extrusion into the adjacent circles of the

connecting pieces (Fig. 10).

D. Securing the Tower

Fan to the Base

• Align the 3 screw holes in

the bottom of the pedestal

with the 3 screw holes

located on the base. Using

the 3 (M5 x 12) screws and

phillips head screw driver

(

), secure the base into

the bottom portion of the

fan housing (Fig. 11).

• Place the power cord

through the cut out on the

bottom of the base. Gently

pull any slack out of the

power cord and place the

cord securely in the power

cord holding bracket

(Fig. 12).

• Place the fan right side up.

Your fan is now ready for use.

HYF013, HYF023 SERIES ASSEMBLY INSTRUCTIONS

Fig. 10

Fig. 11 Fig. 12

Fig. 9

Fig. 7

Fig. 8

Fig. 14

Fig. 15

Fig. 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell DYF012 Series Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info