Bedienungsanleitung Honeywell FG8MS (Seite 2 von 10) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

681056

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

getconnected.honeywell.com

FG8MS

English

1 SELECT MOUNTING LOCATION

Refer to A (on page 1) and the following list for mounting guidelines.

• Mount the detector between the protected glass and any heavy

window coverings that may be present. When heavy window coverings

are present, the detector can be mounted on the frame of the window

• Do NOT mount the detector:

– on posts or pillars

– in rooms with noisy equipment (air compressors, power tools, etc.),

if this equipment is operated when the detector is armed

– where the detector’s view of the glass may be obstructed

unintentionally

2 CONNECT THE BATTERIES (SEE B ON PAGE 1)

3 SELECT PROTOCOL (SEE B ON PAGE 1)

evohome=ALPHA

4 SET THE RANGE (SEE B ON PAGE 1)

For best false alarm immunity, measure distance from the intended

mounting location of the detector to the farthest point of glass to be

protected. The maximum distance should be 7.6 m. Set the shortest

range available with DIP switches SENS 1 and SENS 2 that is greater

than or equal to measured distance.

5 MOUNT THE DETECTOR

Orient the microphone for the best line-of-sight to the protected glass.

If ceiling mounted the end with the microphone should face the

protected glass.

Important: Not suitable for use on acoustic ceiling tiles if the rear

tamper will be used. Use drywall anchors if not mounting to a wall stud

or ceilin joist. If the rear tamper is used, tamper screw should screw

into frame, or a heavy-duty anchor, because the rear tamper requires

high breakawa force. Reinstall the battery (if removed for rear tamper

installation), then close and secure the detector front cover.

6 TEST MODES

TRANSMITTER Test Mode: This test mode shows transmitter activity.

It activates upon power-up and when the cover is opened. It remains

active for 10 minutes after the tamper switch is closed.

GLASSBREAK Test Mode: This test mode allows testing of the

glassbreak function. It is activated three ways – upon power-up,

by pressing the glassbreak test switch (see B on page 1).

For both test modes, refer to the following LED Indicators table.

LED INDICATORS (LEDs are only visible in test mode.)

CONDITION RED LED GREEN LED

Power Up ON 1 second ON 1 second

TRANSMITTER test mode

(10 minutes)

Flashes Brieﬂ y

Once = ALPHA

Flashes Brieﬂ y

Twice = V2GY

OFF

GLASSBREAK

test mode

(5 minutes

)

Normal OFF Flashes once per

second

and Flickers

when sound

detected

Alarm ON 5 seconds

Low

battery

Flashes once per

second

Normal Operation (Not in

test modes)

OFF OFF

5 minutes after the last sound that causes the green LED to ﬂ icker.

When registered, the FG8MS sends a low battery signal to the pane

when the battery voltage gets low. Replace the battery. The detecto low

battery indication is approximate only.

7 TESTING GLASSBREAK WITHOUT AN FG-701 TESTER

Enter GLASSBREAK test mode. The Green LED will ﬂ ash at 1Hz. Clap

hands near the detector and the Green LED will ﬂ icker, verifying the

detector is hearing room noise. To test that that the panel is detecting

an alarm, tap on the detector cover with a ﬁ nger nail or screwdriver until

the Red LED turns on for 5 seconds.

8 REGISTERING THE DETECTOR

https://international.mytotalconnectcomfort.com

Open and close the front cover.

https://international.mytotalconnectcomfort.com

9 INSTALL COVER SCREW, IF REQUIRED

To secure the front cover after installation, remove the cover breakou

ﬂ ash and secure the front cover with a 2.9 mm x 6.0 mm screw (no

provided.) Refer to D on page 1.

10 SPECIFICATIONS

Protected Glass Types:

NOTE: Minimum size for all types is 28cm x 28 cm.

Glass Type* Nominal Thickness

Minimum Maximum

Plate 2mm 10mm

Tempered 3mm 10mm

Laminated

1, 3

3mm 14mm

Wired 6mm 6mm

Coated

2, 3

3mm 6mm

Sealed insulating

1, 3

3mm [13mm overall] 6mm [19mm overall]

* Glass must be framed in the wall or mounted in a barrier at least 0.9m

wide.

Protected only if all plates or panes are broken.

Coated glass with security ﬁ lms up to 0.35mm (14 mils) thick (including

ﬁ lms for solar protection) may be used. Evaluated with the these

products: 3M® SCOTCHSHIELD® SH14CLARL – 0.35mm (14 mils), 4 ply

ﬁ lm; Film Technologies International, Inc.’s GLASS-GARD GGLL 1200.

For these glass types, mounting at less than ½ the indicated range

setting is recommended. (Example: set SENS 1 and SENS 2 for 4.6 m

range, but mount the detector 2.3 m or less from the farthest glass to be

protected.)

FG8MS Wireless Glassbreak Detector –

Installation Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell FG8MS Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info