613651
29
Zoom out
Zoom in
Vorherige Seite
1/90
Nächste Seite
HCE80(R) / HCC80(R) Mounting and operation 25
Activating the cooling function at the CM927
The heating/cooling function is specified by
Parameter 4:HC in the installation mode.
1
Set the slide switch to the "OFF" position.
2
Press the and <, > buttons
simultaneously.
1:CL of the first parameter
level is displayed.
3
Press the > button to change to
the second parameter level.
1:Ot of the second parameter
level is displayed.
14
Press the + button until 4:HC is displayed.
5
If applicable, use the
and
buttons to select the setting "1" and
confirm with the OK button.
The cooling function at the
CM927 is activated.
Enabling the cooling function at the
underfloor heating controller
1
Keep the Mode button pressed
for at least 4 seconds.
The
LED indicates the activated mode:
LED
Meaning
Lights up green Cooling mode
active
Lights up red Heating mode
active
2
Change the setting by pressing
the installation button .
The underoor heating controller
switches back to normal mode
automatically after 60seconds.
You can also exit the installation
mode by pressing the Mode button.
!
Binding the room temperature setpoint cooling
The cooling function at the CM927 has
to be activated to this purpose.
1
Press and hold the installation
button on the underfloor heating
controller for 2 seconds.
The
LED lights up. The LED
of zone 1 flashes green.
2
Press the installation button twice
at the underfloor heating controller.
The LED of zone 1 flashes orange.
The underfloor heating controller
waits for the CM927 signal.
Setting the CM927 to the binding mode
1
Move the slide switch to
the "OFF" position.
2
Keep the
and
and < buttons pressed
simultaneously until InST CO is displayed
2
Send the binding signal by
pressing the OK button.
The cooling setpoint is assigned
to the selected zone.
The LED of the selected zone at
the underfloor heating controller
lights continuously orange.
If cooling is not activated, the
LED of Zone 2 ashes red.
!
Toggling between heating and cooling
at the CM927 operating device
The changeover from heating to cooling operation and
vice versa has to be carried out manually at the CM927.
1
Keep the
and
buttons pressed
for approx. 5 seconds until "Cooling" or
"Heating" respectively is displayed.
The CM927 operates in the displayed
operating mode with immediate effect.
Cooling with CM927
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Honeywell HCE80-R wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Honeywell HCE80-R

Honeywell HCE80-R Bedienungsanleitung - Deutsch - 32 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info