Bedienungsanleitung Honeywell HCE840 series (Seite 3 von 12) (Englisch, Französisch, Spanisch)

723864

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

4 5

6 HEAT SETTINGS THAT GIVE YOU CONTROL OF YOUR COMFORT

SAFETY FEATURES

TROUBLESHOOTING

Problem Solution

If your Honeywell HeatGenius

Ceramic Heater shuts off

unexpectedly or fails to

operate, one of your heater

safety features may have

been activated to prevent

overheating.

• Be sure it is plugged in and that the electrical outlet is working.

• Check for any obstructions. If you ﬁnd an obstruction, turn the heater

OFF (

) and unplug it.

• Allow the heater to cool completely, then remove the obstruction.

Wait at least 10 minutes, then re-plug the heater in and follow the

OPERATION instructions.

• Press and hold both Thermostat Control Buttons (

) for three seconds to change between Fahrenheit

and Celsius and back.

It is recommended that the Honeywell HeatGenius

Ceramic Heater be cleaned at least once a month and

before off-season storage.

• Turn Off (

) and unplug heater. Allow unit to cool.

• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES,

POLISHES OR ANY CHEMICAL SOLUTION.

• Before storing, clean the Ceramic Heater using the above-mentioned steps. Wrap the cord around the

unit. Place in its original box and store it in a cool, dry place.

• This heater does not disassemble.

FAHRENHEIT TO CELSIUS

CLEANING AND STORAGE

Model(s) Unit dims Amps Unit

Voltage

Max

Watts

Max BTUs

HCE840B /

HCE840C

10.2” L x 5.6” W x 17.3” H 12.5 120V, 60Hz 1575 5118

PRODUCT SPECIFICATIONS

Fig. 3

Fig. 2

Low Heat

& "White

Noise"

Setting

2 Hour

Auto-off

Timer with

30 Minute

Phased

Intervals

6 Ways to Heat the Space You are In - Once your heater is ON, use the control buttons on the bottom to

select the desired heat setting for your needs. Your heater will start on the Constant Hi Room heat setting

each time you turn the heater on. Here is a handy reference to help select the heat option that best suits

your desired comfort level:

FLOOR AREA – (LOW HEAT)

This setting uses the lower level heating element only to provide a comfortable, gentle heat to warm up the

ﬂoor area in front of the heater.

PERSONAL – (MODERATE HEAT)

This setting uses a moderate heat level to warm you personally wherever you may be relaxing (reading,

watching TV, etc.). The LO option (

) provides a soothing heat level, while the HI option ( ) slightly

increases heat output, allowing you to adjust to your desired comfort level.

ROOM – (MODERATE-HIGH HEAT)

Best for whole room heating, use this setting to bring warmth to cooler, drafty rooms. The LO option

provides a moderate heat level, while the HI option uses maximum heat output to create a warmer

environment.

THERMOSTAT – (MODERATE-HIGH HEAT)

To set the Thermostat, press the Thermostat Control Buttons (

) to choose your Desired

Temperature. The Desired Temperature will ﬂash ﬁve times and then the Current Temperature in the room

will display as a steady number. The Thermostat can operate on either HI or LO heat levels to achieve

Desired Temperature by pressing the (

) button under Room.

NOTE: If the Current Temperature is higher than your Desired Temperature, the heater will go into cool down

mode and then shut-off until the room temperature falls below this setting or until the Desired Temperature

is changed.

HEATPHASE™ TIMER

The new HeatPhase Timer is an auto-off feature that gradually transitions the room temperature from

warmer to cooler. The timer starts at high heat and steps down 4 different heat levels until it shuts off - over

a 2 hour period. This feature is ideal for setting a comfortable, relaxing environment. (Fig. 2) The timer can

also be toggled to start at whichever level desired.

QUIET MODE

The new Quiet Mode features uses a low heat setting and fan speed to produce a gentle "white noise" and

soothing warmth. (Fig. 3)

The Honeywell HeatGenius

Ceramic Heater is equipped with several devices and features for

added protection:

• A four way tip-over switch that disables the heater if it is accidently tipped in any direction. If tipped over,

the unit should be set upright and follow the OPERATION instructions.

• A high temperature safety control prevents overheating. If activated, unplug the device and wait at least

10 minutes for unit to cool. Then plug the heater back in and follow the OPERATION instructions.

• The heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater should

it operate at a highter than normal temperature. If activated, the unit will need to be replaced.

• This heater was created using high quality, heat-resistant plastics and has a Cool Touch handle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HCE840 series Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info