Bedienungsanleitung Honeywell HFD-013 Series (Seite 4 von 15) (Englisch, Französisch, Spanisch)

723802

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

6 7

CAUTION: Turn OFF and unplug the air purifier

To remove the ifD

Micro-filter:

• Push the Filter Release button and then gently lift the

filter assembly (Fig. 10a & 10b). The filter assembly will

only release if the button is pushed.

• Remove the pre-filter press the top tab to the relase the

pre-filter (Fig. 14).

• With one hand, hold the air purifier frame and use other

hand to grasp ifD

filter and pull out (Fig. 14b).

To clean the ifD

Micro-filter:

The ifD

filter should be cleaned approximately every 3 months.

After removing the ifD

filter from the air purifier, follow the steps below to

clean the ifD

filter.

• VACUUM: (Optional) After removing the ifD

Micro-filter from the air purifier,

gently run a vacuum cleaner with a nozzle or brush attachment along the filter

to pick-up tiny particles (Fig. 11). Repeat on both sides.

WASHING:

If you choose not to vacuum the filter first, please follow the steps below to wash

the ifD

Micro-filter.

• Remove the ifD

Micro-filter from the unit.

• You can simply rinse the ifD

Micro-filter under the faucet, or for more thorough

cleaning, fill the sink with lukewarm water and add a few drops of mild dish

soap (Fig. 12).

• Gently swish the filter in the soap solution to clean.

• Soak the filter for 2-3 minutes. Do not leave for an extended period of time.

• Rinse the filter with clean tap water.

DRYING:

• Shake the filter to remove any excess water.

• Place the filter with the honeycomb side down on a plush towel (Fig. 13).

• Note that the filter may still be discolored even after washing.

This is acceptable and will not affect performance.

• Allow the ifD

Micro-filter to dry for a few hours or overnight.

• When the ifD

Micro-filter is completely dry, place back into the air purifier.

Make sure you insert the filter according to the directional arrows on the filter.

To place the ifD

filter back into the housing, align the filter assemby with the

opening at top of unit and insert. Press until it is flush and you hear an audible

“click”.

Fig. 10a

Fig. 10b

Fig. 11

Fig. 12

Fig. 13

REMOVING / CLEANING THE IFD

MICRO-FILTER (ALL MODELS)

•

To replace washable pre-filters with the Odor-Lock

™

pre-

filters, remove the standard washable pre-filter assembly

by pushing on the top tab (Fig.17).

•

To insert the Odor-Lock

™

pre-filters into the pre-filter

frame, line the tabs on the pre-filter up with the frame

notches and snap into place (Fig.18).

•

Install the Odor-Lock

™

filter assembly by inserting the

lower tab of the pre-filter frame into the filter assembly

until you hear a “click” (Fig. 19.

•

Align the complete filter assembly with the opening in

the unit and insert back into the unit (Fig. 20).

NOTE: The Odor-Lock

™

filters are not washable.

NOTE: If Odor-Lock

is used in lieu of the permanent

washable pre-filter, it will need to be replaced approximately

every 3 months and should be installed the same location

after the washable pre-filter is removed.

INSTALLING THE ODOR-LOCK

™

PRE-FILTER(S) (HFD-014, HD010WHS, HD010LHS, HD010RHS ONLY)

Fig. 17

Fig. 18

Fig. 19 Fig. 20

REMOVING/CLEANING THE WASHABLE PRE-FILTER (ALL MODELS)

To remove the pre-filter:

•

Press the top tab to release the pre-filter from the filter

assembly (Fig. 14).

•

Hold the frame steady from the side while pushing in the

center of each pre-filter from the back side of the frame

(Fig.15).

•

Separate the pre-filter from the frame and you can then

pull it completely away from the frame (it will snap out).

•

If using the Odor-Lock

adsorbing pre-filter, it is recommended that you store the original washable

pre-filter in the event that you decide to use it in the future.

Fig. 14

Fig. 16

To clean the pre-filter:

The particle pre-filter helps pick-up large airborne particles that enter the filter.

This pre-filter can be periodically removed and shaken or vacuumed clean.

Alternatively, it can be rinsed by hand under warm water to clean (Fig. 16).

Let the pre-filter dry completely before inserting it back into the unit.

Fig. 15

CAUTION:

• Never place a wet ifD

Micro-filter in your air purifier.

• The ifD

Mirco-filter is NOT dishwasher safe. Do not place the ifD

Micro-filter

in a dishwasher or subject it to other extreme hot water conditions.

• Do not use any solvents, strong cleaning agents or flammable liquids to clean

the ifD

Micro-filter.

Fig. 14

Fig. 14b

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HFD-013 Series Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info