5
ENGLISH
3. Attach the front and rear bases (1+2) to the underside
of the fan using the four cross recess screws. Make sure
that the front and rear bases (1+2) are securely fixed to the
fan.
4. Push the power cable (5) through the track (4) on the
underside of the rear base (2) to the outside.
5. Stand the fan upright. Make sure that the power cable
(5) leads through the opening on the rear base (2) and that
the base (1+2) is not resting on the power cable (5).
REMOTE CONTROL
1. Put the two AAA, 1.5V batteries into the battery
compartment (8) and push the cover (9) back until you
hear it click into position. The maximum distance for
transmitting signals between the remote control (7) and
the fan is five meters. Make sure that no objects can
impede signal transmission.
2. When you are not using the remote control (7), keep it
in the slot (10) provided at the top of the fan.
3. When you change the batteries, use only new alkaline
batteries AAA, 1.5 V. and dispose of the used batteries for
recycling according to your local regulations.
4. If you are not going to use the remote control (7) for a
longer period (4 weeks or more), take the batteries out of
the battery compartment.
INSTRUCTIONS FOR USE
1. Place the fan on a firm, even surface. Make sure it is
standing securely so that it cannot tip or fall over. A safety
distance of at least 50 cm from other objects must be
observed.
2. Make sure that the fan is switched off. Push the power
plug (5) into the power socket. Insert the batteries into the
remote control (7).
3. You can control the fan manually via the control panel
(11) or with the remote control (7).
4. Press this key (13) to switch on the fan. You can
set the fan speed by pressing the key (13):
„I“ = low
„II“ = medium
„III“ = high.
The respective control light „I“, „II“or „III“ (17) lights up.
The fan is operating with the normal fan function.
5. Press the oscillation key (15) to start the fan
oscillating from left to right. To stop the oscillation, press
this key (15) again.
6. By pressing this key (16) you can choose between
two operating modes that simulate a natural breeze:
: The control light (19) lights up green:
The fan switches itself on and off and simulates a natural
breeze by changing the intensity of the air flow. Choose a
speed „I“, „II“or „III“. The air flow intensity varies
between weak –strong – weak – off.
: the control light (19) lights up green (night diming):
The fan switches itself on and off and simulates a natural
breeze by changing the air flow intensity. Choose speed
level „III“. After operating for half an hour the fan reduces
the speed automatically to level „II“ and after a further half
hour to level „I“. The fan operates at speed level „I“ until it
is switched off. During the whole running period the fan
changes the air flow intensity from off via weak to strong.
The speed control lights (17) change according to the
lower speeds.
By pressing the oscillation key (15), you can start
the fan oscillating from left to right on both operating
modes.
7. The fan is equipped with a „TIMER“ function. This
function switches the fan off after the set time ends. The
time period is at least 30 minutes and at the most 7.5
hours and can be set at intervals of 0.5h by pressing the
timer key (14). The respective timer control lights
(17) light up. Examples:
Press x 1: 0.5h – control light „0.5h“ lights up green
Press x 5: 2.5h – control lights „2h“ and „0,5h“ light up
green
Press x 10: 5.0h – control lights „4h“ and „1h“ light up
green
Press x 15: 7.5h – control lights „4h“, „2h“, „1h“ and
„0,5h“ light up green
To deactivate the „TIMER“ function, press the key
(14) repeatedly until all the timer control lights (18) are off.
8. Use the transport grip (6) to transport the fan. Before
transport, switch off the fan with the key (12) and pull
the power plug (5) out of the power socket.
9. When you have finished using the fan, switch it off with
the key (12) and pull the power plug (5) out of the
power socket.
CLEANING AND STORAGE
We recommend that you clean the fan and the remote
control (7) regularly.
So as not to disrupt the functioning of the fan and remote
control (7), please follow the instructions given below.
