Bedienungsanleitung Honeywell HPA030 (Seite 4 von 24) (Englisch, Französisch, Spanisch)

723814

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

This model air purifier has an electronic filter check to remind you

when to check and replace the True HEPA filters and pre-filter

based on the air purifier’s hours of use. A red LED will illuminate

when it is time to check/replace the filters.

When the True HEPA filters or pre-filter need to be replaced,

the light will remain on until it is RESET. You may unplug the air

purifier without interrupting the filter check.

You should periodically check the filters. Depending on operating

conditions, the True HEPA filters should be replaced every

12 months and pre-filter every 3 months.

REPLACE WITH TRUE HEPA FILTER and ODOR

REDUCING PREFILTER

These cleaning intervals are intended as guidelines only.

Performance of any filter media is dependent upon the

concentration of contaminants going through the system. High concentrations of contaminants such as dust, pet

dander and smoke will reduce the useful performance of the filter.

NOTE: None of the filters are washable. DO NOT immerse them in water.

To RESET the Electronic Filter Check:

When the Check Filter LED remains on and solid, it is time to replace the Odor Reducing Pre-filter and reset the

filter monitor. With the unit powered ON, press the FILTER RESET button below the Check Filter LED and hold for

approximately 2 seconds until the light turns off (Fig. 4).

When the LED illuminates and is flashing, it is time to replace the True HEPA filters and reset the filter monitor.

With the unit powered ON, press FILTER RESET button and hold for approximately 2 seconds

until the light turns OFF (Fig. 4).

Manual (or Early) Reset of Electronic Filter Check

Depending on your individual usage (environment and hours used), you may need to replace the filters more or

less frequently. Each time you replace your filters, you should reset the filter monitor. You may manually reset the

filter monitor for the pre-filter or the HEPA filter, or both. If you change the pre-filter or True HEPA filter before the

Check Filter LED is illuminated, it is possible to reset the filter monitor. You must first manually illuminate the

Check Filter LED. Follow these steps:

1. With unit powered ON, press the FILTER RESET button for 5 seconds to illuminate the LED in “solid” mode.

2. To reset filter monitor for pre-filter: press and hold FILTER RESET button for 2 seconds until LED changes to

flashing mode.

3. TAP FILTER RESET button to shut LED off. The pre-filter monitor is now set to “clean status”.

4. To reset filter monitor for HEPA filter: LED must be in “flashing mode”. Follow Step 1 above, then TAP FILTER

RESET button again to illuminate the LED in “flashing mode”.

5. Press and hold FILTER RESET button for 2 seconds until LED shuts off. The HEPA filter monitor is now set to

“clean status”.

6. To reset filter monitor for both pre-filter and HEPA filter: Follow Steps 1,2, and 5 above.

ELECTRONIC FILTER CHECK REMINDER

Will illuminate when it is time to replace the

True HEPA Filters or Odor Reducing Pre-filter

Fig. 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HPA030 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info