Bedienungsanleitung Honeywell HPA300 series (Seite 2 von 12) (Englisch, Spanisch)

723798

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

2 3

HPA100 series, HPA200 series, HPA300 series

Type

Odor Reducing Pre-Filter

Household Gas

& Odor Reducing Pre-Filter

Front Grille

YOUR AIR PURIFIER

SET-UP

• Select a firm, level and flat location.

• When operating, large volumes of air are drawn toward the air purifier. Surrounding areas should be

cleaned and/or vacuumed frequently to prevent build-up of dust and other contaminates. This may

also help prolong the life of the filter. If the unit is placed on a light colored carpet, a small mat or rug

should be used underneath to prevent permanent staining. This is especially important in homes with

contamination from smoking, fireplaces, or where candles are burned.

• Ensure the front of the unit faces away from the closest wall or furniture.

• Ensure no grilles are blocked.

Control Panel

HPA090 series

Type

True HEPA

Filter (1)

Type

Odor Reducing

Pre-Filter or

Household Gas &

Odor Reducing Pre-Filter

Front Grille

The True HEPA Filters and Odor Reducing Pre-Filter are supplied within the air purifier. New air purifiers

have their filters wrapped to ensure purity, and are labeled to help identify the proper replacement filter.

(

Type

True HEPA Filter; Type

Odor Reducing Pre-Filter or

Household Gas & Odor Reducing Pre-Filter)

• Before using your new air purifier you must remove the wrappers covering the filters and Pre-Filter.

Make sure the air purifier is OFF and unplugged. Press the two hand symbols (

) on the front grille to

release it from the unit and pull the grille toward you to remove it (see Fig. 2). Grasp the sides of the

filter frame near its top end and pull outward. Repeat for the second and third

filter if applicable.

• Remove protective wrap from the filters (including the Pre-Filter) that have

been supplied with your air purifier.

• Place the HEPA filter(s) into the air purifier housing. Ensure that the removal

“pull” tabs are facing outward (this will facilitate filter removal later). Place the

Pre-Filter on top of the HEPA filter(s). Tuck the edges of the Pre-Filter into the

tabs that are located around the edges of where the HEPA filter(s) are inserted.

This will hold the Pre-Filter securely in place.

• Replace the front grille by placing the tabs on the bottom of the grille into the

slot(s) on the unit. Gently push the top of the grille into place by pressing on the hand symbols (

) to

secure in place.

Control Panel

Type

True HEPA Filters

HPA100 HPA300HPA200

HOW YOUR AIR PURIFIER WORKS

This model air purifier incorporates a 2-stage cleaning

system to help clean the air that passes through the

filter in the unit (Fig. 1).

Stage 1: Odor Reducing Pre-Filter

Stage 2: True HEPA Filter that captures

particles as small as 0.3 microns or larger

Filter(s)

Odor Reducing

Pre-Filter

STAGE 1

STAGE 2

Fig. 1

SET-UP

INSTALL TRUE HEPA FILTERS AND ODOR REDUCING PRE-FILTER

Fig. 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HPA300 series Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info