Bedienungsanleitung Honeywell HS-216E (Seite 4 von 50) (Alle Sprachen)

695196

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

1. Please read all instructions before using this fan.

2. Only use this fan as described in this manual. Other non-

recommended use may cause fire, electric shock, or injury.

3. Only connect the fan to a single-phase power socket with the

current as stated on its type plate.

4. Connect power after the fan has been fully assembled. Unplug

from outlet when moving fan from one location to another,

before putting on or taking off parts and before cleaning.

Disconnect the fan when not in use. Do not tug at the power cord

to disconnect the plug.

5. Supervision is needed when the fan is used anywhere near

children. This appliance is not intended for use by children or

other persons without assistance or supervision if their physical,

sensory or mental capabilities prevent them from using it safely.

6. If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person in

order to avoid a hazard.

7. Unwind the power cord completely. An incompletely unwound

power cord can lead to overheating and cause a fire. Do not touch

the power cord with wet hands. Position the power cord so that

nobody can trip over it and where the socket can be reached

easily.

8. Do not use an infinitely variable speed controller. This can lead

to overheating, fire, electric shock or faults in the appliance.

9. Do not operate the fan without the protective front and rear

grilles in position. Do not touch the rotating fan blades with any

part of the body. This can cause personal injury and damage.

10. Never insert fingers, pencils, or any other object through the

grille when fan is running.

11. Do not operate the fan if it is damaged or might be defective,

or if he is not working properly. Remove the power plug from the

socket.

12. Do not use the fan anywhere near easily inflammable gases or

substances such as solvents, lacquers, glues etc.

13. The fan is only designed for private use in indoor rooms and

is not intended for outdoor or for commercial use. Do not use the

fan anywhere near a bathtub, a shower or a swimming pool, or

anywhere else where water could splash.

14. Do not plunge the fan into water or any other liquids and do

not pour water or any other liquids over the fan.

15. Place the fan on a firm, even, dry surface. Be sure the fan is on

a stable surface when operating to avoid overturning. Make sure

the fan is standing securely so that it cannot tip over or fall down.

Maintain a safety distance of at least 50 cm from other objects.

16. Clean the fan regularly by following the cleaning instructions.

COMPONENTS

1. Front Grille

2. Blade

3. Plastic Nut

4. Rear Grille

5. Plastic Sleeve on Motor Shaft

6. Oscillating Control Knob

7. Neck

8. Control Knob

9. Extension Column

10. Height Adjustment Ring

11. Column

12. Stand Ornament

13. Stand Base

ASSEMBLY INSTRUCTIONS

Stand Base Assembly

1. Take the stand base and column parts from the packing box

and loosen the four screws (Fig. 1).

2. Fix the column on the stand base using the 4 sets of screws

(Fig. 2).

3. Unscrew and remove the height adjustment ring and mount

the column ornament. Replace and screw the height adjustment

ring to tighten the extension column at the appropriate height

(Fig. 3).

Assembly of Blade and Grilles

1. Unscrew the spinner clockwise and the nut counter-clockwise

to separate them. (Steps 1, 2, and 3 - Fig. 4)

2. Set the rear grille in the proper position with handle up.

3. Screw on plastic nut tightly to attach rear grille.

4. Discard plastic sleeve on motor shaft. Install the blade onto the

shaft until it reaches the retaining pin (Steps 4, and 5- Fig. 5).

5. Screw spinner onto motor shaft counter clockwise to blade.

6. Press the front grille onto the rear grille until the front grille is

properly fitted, fix both grilles with rim and use a screw driver to

tighten the locking screw (Fig. 6).

7. Secure both grilles firmly by tightening the fan grille locking

screws and nuts (Fig. 7).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HS-216E Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info