Bedienungsanleitung Honeywell HT-900 Series (Seite 3 von 11) (Englisch, Französisch, Spanisch)

723847

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

WALL MOUNTING

(HT-800 Series and HT-900 Series Only)

• Locate and mark the position on the wall where the fan will be mounted (preferably at a wall stud).

• Insert two screws into the wall stud. (Screws are not included and can be purchased at a

hardware store)

• Use #8, 1” length screws, leave 3/8” below screw head (bolt) exposed from the wall.

• Line up the openings on the base of the fan with the screws (bolts) and hang the fan on the wall.

NOTE: HF-910 Series and HT-908 Series cannot be wall-mounted

CLEANING AND STORAGE

Unplug the fan before cleaning.

• These fans are equipped with a cord wrap feature for storage on the bottom of

the fan (Fig. 7).

• Use only a soft, damp cloth to gently wipe the fan clean.

• DO NOT immerse the fan in water and never allow water to drip into the motor

housing.

• DO NOT use gasoline, paint thinner or other chemicals to clean the fan

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

REMOVAL OF THE FRONT GRILLE FOR CLEANING

DO NOT remove the fan grille unless the power is turned off and the

power cord is unplugged.

• Gently lay the fan face down on a table (Fig. 8).

• Screws are located in the holes around the back grille of the fan (Fig. 9).

• After the screws in each hole are located, insert a standard Phillips Head

screw driver into one of the screw holes.

NOTE: Screwdriver head should fit comfortably in the hole without being

too tight or leaving too much room. A screwdriver with a head that is too

small will have trouble engaging the screw.

• Each screw should be engaged and loosened by unscrewing each head

to the left.

• Once all screws have been loosened, slowly lift the fan up off the surface using

the back carrying handle, and separate the front grille along the seam where

the screws were located (Fig. 10).

NOTE: Screws will sometimes fall out of the back of the unit once loosened,

so be sure not to stand the fan up or tip it over too quickly.

• To reassemble the fan, collect all of the screws and lay the fan on its back

(Fig. 11).

• Place the front grille onto the unit, lining up the notch in the grille, with the

notch along the bottom of the fan (Fig. 12).

• Once the grille is aligned with the body of the fan, and each screw hole

matches up, flip the unit to lay it face down on a flat surface.

• Insert each screw into a hole and gently tighten each screw. Ensure that the

front grille and the bottom of the fan are tightly secured together.

• For storage, clean the fan carefully as instructed. Store the fan in the original

packaging or cover the product to protect it from dust.

OPERATION

• Be sure the fan is in the OFF position.

• Place your fan on a dry, level surface.

• Plug the power cord into a polarized 120 volt AC wall outlet.

• To operate, turn the control knob to the desired fan speed: HIGH (III), MEDIUM

(II) or LOW (I) (Fig. 5).

• Adjust the fan to the desired angular air output direction.

• To move the fan, turn the fan OFF and pick it up by the concealed handle

that is located on the outside rim of the fan (Fig. 6).

Fig. 5

Fig. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell HT-900 Series Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info