Bedienungsanleitung Honeywell T4R (Seite 2 von 2) (Englisch)

689550

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Parameters

Description Settings (default in bold)

1:LA

Language 1 = EN, 2 = NL, 3 = FR, 4 = DE, 5 = ES, 6 = IT

2:CR

Heating Cycle Rate (cph) 3 (oil boiler / thermal actuator)

6 (gas or combi boiler / zone valve)

3:OT

Minimum on time 1 - 5 (mins) (set to 4 mins for oil boiler)

4:LL

Lower Temperature Limit 5 - 21 (°C)

5:UL

Upper Temperature Limit 21 - 35 (°C)

6:SO

Schedule options 1 = 7 day (different schedule each day of the week)

2 = 5 + 2 day (weekday + weekend schedule)

3 = 1 day (same schedule every day)

7:NP

Number of periods per day 4 or 6

9:LC

Fail Safe mode 0 = Boiler off, 1 = Boiler 20% on / 80% off

10:BL

Backlight 0 = Off, 1 = On (only on demand)

11:CL

Clock Format 0 = 24 hr, 1 = AM/PM

12:DS

Daylight Saving time change 0 = Off, 1 = Auto

13:TO

Temperature Display Offset +/1.5°C

15:SD

Restore Schedule Defaults 0, 1 = reset

16:FS

Restore Factory Settings 0, 1 = reset

Configure the System

Specific settings for the thermostat

and heating system can be

configured in the advanced menu.

Press and hold

and then

buttons together until the display

changes (approx. 3sec).

A) Press

and buttons to navigate

through the parameter list

B) Press

and buttons to

change a parameter

C) Press

button to save the change

(or press to cancel the change)

D) Press

button to exit advanced

menu and save any changes

Parameter

Number

Parameter

Setting

Troubleshooting

Manufactured for and on behalf of the Environmental & Energy Solutions

Division of Honeywell Technologies Sàrl, ACSE&ES, Z.A., La Pièce 16,

1180 Rolle, Switzerland by its Authorised Representative Honeywell Inc.

Honeywell Control Systems Ltd.

Skimped Hill Lane,

Bracknell,

Berkshire

RG12 1EB

www.honeywelluk.com

Conforms to protection requirements of the following directives:

EMC: 2014/30/EU, LVD: 2014/35/EU and R&TTE: 1995/5/EC

Hereby, Honeywell, declares that this Thermostat is in compliance with the

essential requirements and other relevant provisions of Directive 2014/53/EU.

ErP: Class V (+3%), (EU) 811/2013, Receiver Category 2

WEEE Directive 2012/19/EC

Waste Electrical and Electronic Equipment directive

At the end of the product life dispose of the packaging and product in a corresponding recycling

centre. Do not dispose of the unit with the usual domestic refuse. Do not burn the product.

To rebind the thermostat and receiver box

OpenTherm® Compatibility

The thermostat and receiver box in this pack are pre-bound. Follow these

instructions only if binding is required.

To enter the binding menu press and hold

and then buttons together until

the display changes (approx. 3sec), and follow steps A) to D) above to navigate

the binding parameters. Keep at least 1m between devices during binding.

A) Clear the binding data from the Receiver Box:

Press & hold the reset ‘pinhole’ button for 3sec.

B) Put the Receiver Box into bind mode:

Hold

button for 3sec - button lights ORANGE for

3sec followed by LED ﬂashing ORANGE.

C) Put the Thermostat into bind mode:

Change parameter N

14 A

(RF Binding Mode) to ‘1’ and press

If successful the Receiver Box LED willl turn solid

GREEN and the Thermostat will show

OpenTherm® compatibility is offered only by the Receiver Box. The Thermostat will

control heat demand as normal but will not show OpenTherm® specific boiler data

on the display - Refer to the boiler instructions for how to view the boiler data.

What’s happening? What it could mean... How to fix it...

Thermostat display

is blank

Batteries exhausted,

installed incorrectly or

tab hasn't been removed

Pull thermostat from wall bracket or table

stand and check battery installation

- replace batteries if necessary

Display =

Battery power critically low Pull thermostat from wall bracket or table

stand and check battery installation

- replace batteries if necessary

Display =

Faulty temperature sensor Replace thermostat or check wiring to

remote temperature sensor if fitted

Thermostat shows heat

demand

but boiler

doesn't respond

Boiler (water) already

at temperature

Normal behaviour - wait for

water temperature to drop

Faulty wiring connection Check wiring at thermostat and boiler terminals

Thermostat display shows

and Receiver Box

LED is flashing RED

Wireless communication

with Receiver Box is lost

Move thermostat to a location where

wireless communication is reliable

Thermostat display shows

and Receiver

Box

LED is OFF

Thermostat and Receiver

Box not bound

Follow the Wireless Binding Instructions

Receiver Box

LED

is flashing ORANGE

Receiver Box is in

bind mode

Wait for bind mode to time out

(3min) or bind a Thermostat

Description Settings (default in bold)

14:A

RF Binding Mode 0, 1 = Enter bind mode

14:B

RF Signal Strength Test 0, 1 = Perform Signal Test

14:C

Delete RF Binding Data 0, 1 = Delete Bind Data

Press

for 3sec

to clear

binding

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell T4R Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell T4R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info