Bedienungsanleitung Honeywell TB6980 (Seite 6 von 6) (Englisch)

32697

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

TB6980/TB7980 62-0238 400-150-005-B 3/23/06 6/6

5.4.2 Changeover Input

The thermostat is in the default mode when the contact between ter-

minals 9 and 11 is open and switches mode when the contact is

closed. The default mode is set via the configuration menu .

Note: The changeover contact state is ignored if the thermostat is

configured in automatic changeover or in limited cooling.

5.5 Night Setback

The Night Setback (NSB) mode is activated when the

contact between terminals 9 and 12 is closed. When the

thermostat is in the NSB mode, indicated by the ECONO

display, the temperature is lowered or raised by the set

NSB value depending whether the thermostat is in heat

mode or cool mode respectively. The NSB value is set via the con-

figuration menu.

Night Setback Override

To temporarily override the NSB mode, press the Over-

ride button. The NSB mode is lifted for the next 2 hours

or until the Override button is pressed again. During the

override, the normal setpoint is used and OVERRIDE is

displayed.

5.6 Error Codes

The following error codes can appear at the top of the display.

E1: The internal temperature sensor is defective

E2: The internal temperature sensor is shorted

E3: The external temperature sensor is defective or not connected

E4: The external temperature sensor is shorted

6. Technical Specifications

Power: 24 VAC

Current consumption: 25 mA

Output signals: Depends on output configurations

Setpoint range: 10°C to 35°C (50°F to 95°F)

Temperature display: 0°C to 60°C (32°F to 140°F)

Temperature display resolution: 0.5°C (1°F)

Mode hysteresis: 2°C (4°F)

Automatic changeover deadband: 5°C (9°F)

Duty cycle: Depends on output configurations

NSB offset: Programmable 1°C to 9°C (2°F to 18°F)

NSB override period: 2 hours

Memory protection: Configuration and setpoint

Temperature control: Proportional integral adaptive (P.I.A.)

Operating temperature: 32°F to 140°F (0°C to 60°C)

Storage temperature: -4°F to 122°F (-20°C to 50°C)

Humidity limits: 0 to 95% R.H., non-condensing

Dimensions: 69 x 118 x 27 mm (2.7 x 4.6 x 1.0 in.)

Accessories: - R841 electromechanical relay

- 50014157-001 air duct temperature sensor

- 50014156-002 remote temperature sensor

Compatible Damper/Valve actuators

VC6930, VC6934, VC6936

VC7930, VC7934, VC7936

ML6984

ML7984

ML6410, ML7410

ML6161B2024, MN6105A1011

ML7161A2008, MN7505A2001

Wiring: 18 AWG (1 mm

) wire

Mounting: - directly to drywall

- single-gang NEMA standard 2-in x 4-in electrical box

- double-gang NEMA standard electrical box with

mounting plate

7. WARRANTY

Honeywell warrants this product, excluding battery, to be free from defects in

the workmanship or materials, under normal use and service, for a period of

two (2) years from the date of purchase by the consumer. If at any time

during the warranty period the product is determined to be defective or

malfunctions, Honeywell shall repair or replace it (at Honeywell's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place

from which you purchased it, or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will

make the determination whether the product should be returned to the

following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885

Douglas Dr N, Golden Valley, MN 55422, or whether a replacement

product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty

shall not apply if it is shown by Honeywell that the defect or malfunction was

caused by damage which occurred while the product was in the possession

of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product

within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR

INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR

IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do

not allow the exclusion or limitation of incidental or consequential damages,

so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL

MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED

WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO

THE TWO-YEAR DURATION OF THIS WARRANTY. Some states do not

allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights

which vary from state to state.

If you have any questions concerning this warranty, please write Honeywell

Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call

1-800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell

Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario

M1V4Z9.

8. SERVICE

If you have any questions about the operation of your thermostat,

please go to http://customer.honeywell.com, or call Honeywell

technical hotline at 1-763-954-6464.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell TB6980 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info