Bedienungsanleitung Honeywell TL7235A (Seite 1 von 1) (Englisch)

32806

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

TL7235A

User Guide

Non-programmable Thermostat

TL7235A 69-1802 3/5/05 1/1

Honeywell’s TL7235A thermostat can be connected to an electric heater to

control the room temperature.

* The thermostat displays the heater duty cycle required to maintain the desired tem-

perature. For example, if the heater is activated 40 percent of the time, is dis-

played.

• To remove the control module from the

power base, loosen the captive screw

underneath the thermostat and pull the two

components apart as shown.

• To install the control module onto the power

base, reverse the above procedure.

NOTE: Always keep the thermostat's vents clean

and unobstructed.

You can select the temperature display (°F or °C) using a

DIP switch (S1) on the back of the control module.

As soon as the thermostat is powered, it undergoes a series of

tests before displaying the actual temperature.

LO: The measured temperature is below 32°F (0°C). Heating is

activated.

HI: The measured temperature is above 122°F (50°C).

The display illuminates for 5 seconds when the backlight button is pressed.

When either of the buttons is pressed, the display illuminates for 10 sec-

onds.

The thermostat normally displays the actual temperature. To view the set-

point, press one of the buttons once. The setpoint will appear for 5 sec-

onds. To change the setpoint, press one of the buttons until the desired

temperature is displayed. To scroll the setpoint faster, do not release the but-

ton.

Power supply: refer to the power base installation instructions

Setpoint range: 40°F - 86°F (5°C to 30°C)

Display resolution: 1°F (0.5°C)

Storage: -4°F to 120°F (-20°C to 50°C)

Heating cycle length: 15 minutes

Honeywell warrants this product, excluding battery, to be free from defects in the work-

manship or materials, under normal use and service, for a period of five (5) years from

the date of purchase by the consumer. If at any time during the warranty period the prod-

uct is determined to be defective or malfunctions, Honeywell shall repair or replace it (at

Honeywell's option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which

you purchased it, or

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the

determination whether the product should be returned to the following address:

Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley,

MN 55422, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not

apply if it is shown by Honeywell that the defect or malfunction was caused by damage

which occurred while the product was in the possession of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product within the terms

stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF

ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states

do not allow the exclusion or limitation of incidental or consequential damages, so this

limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON

THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-

POSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which vary

from state to state.

If you have any questions concerning this warranty, please write Honeywell Customer

Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Can-

ada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic

Drive, Scarborough, Ontario M1V4Z9.

If you have any questions about the operation of your thermostat, please go to

www.honeywell.com/yourhome, or call Honeywell Customer Care toll-free

at 1-800-468-1502.

Description

Display

% of duty cycle 1 to 24% 25 to 49% 50 to 74% 75 to 99% 100%

Assembly/Disassembly

Configuration

Power-up

Error Messages

Backlight button

Temperature

adjustment buttons

Set the switch to

Off to cut power to

the heater

Heating power *

Temperature

display

Appears when

the setpoint is

displayed

Backlight

Temperature Setting

Technical Specifications

;

Warranty



Customer Assistance

10.

Printed in China

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell TL7235A Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Honeywell TL7235A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info