Bedienungsanleitung Honeywell Y9120W Sundial RF2 Pack 4 (Seite 1 von 26) (Englisch)

613690

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

User Guide

Y9120W Sundial RF

Pack 4

How to use:

ST9120C Wireless Enabled Timer

CS92A Wireless Cylinder Thermostat

Honeywell Control Systems Ltd.

Arlington Business Park,

Bracknell

Berkshire

RG12 1EB

Technical Help Desk: 08457 678999

www.honeywelluk.com

50047645-002 A

System Components

Energy Efﬁciency and the Environment

Home energy use is responsible for more than ¼ of the total UK carbon emissions

which contribute to climate change. Heating and hot water systems based on

boilers account for of this ﬁgure, so it is important to understand how your

controls can help to maximize energy efﬁciency while maintaining your comfort.

Your Timer should be used in conjunction with appropriate temperature controls. In

order to save energy the following general points should be observed:

1. Ensure your system contains a room thermostat (where appropriate) and a hot

water thermostat, and that it is set to an appropriate temperature level, typically

20°C

2. Programme your heating (and hot water) to be off when you are not in the

house. If you are concerned about possible frost damage to any exposed pipe

work, it is advisable to ﬁt a frost protection system – your installer can advise

you about this.

3. Think about how you use your domestic hot water – if you have a storage

system, it is not necessary to have this switched on all the time, even when you

are in the house.

4. Consider the heat up times required for your central heating. Every home

responds differently when the heating is switched on. Adjust the start time so

that you are not cold when you get up in the morning. A shorter heat up time is

required for other heating periods.

5. In the evening, when the house is up to temperature, it is often possible to

switch off the heating up to an hour before you go to bed, without any noticeable

reduction in comfort.

PLEASE RESPECT YOUR ENVIRONMENT!

Take care to dispose of this product and any

packaging or literature in an appropriate way

This document is to be left with the user

and forms part of a Home Information Pack

WHAT IS A PROGRAMMER?

...an Explanation for Householders (as recommended by the Energy Savings Trust)

Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and

domestic hot water on and off at the same time, while others allow the domestic hot water and heating

to come on and go off at different times. Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On

some programmers you must also set whether you want the heating and hot water to run continuously,

run under the chosen ‘On’ and ‘Off’ heating periods, or be permanently

off. The time on the programmer must be correct. Some types have to be

adjusted in spring and autumn at the changes between Greenwich Mean

Time and British Summer Time. You may be able to temporarily adjust the

heating programme, for example, ‘Override’, ‘Advance’, or ‘Boost’. These

are explained in the manufacturer’s instructions. The heating will not work

if the room thermostat has switched the heating off. And, if you have a hot-

water cylinder, the water heating will not work if the cylinder thermostat

detects that the hot water has reached the correct temperature.

WHAT IS A CYLINDER THERMOSTAT?

...an explanation for Householders (as recommended by the Energy Savings Trust)

A cylinder thermostat switches on and off the heat supply from the boiler to the hot water cylinder.

It works by sensing the temperature of the water inside the cylinder, switching on the water heating

when the temperature falls below the thermostat setting, and switching it off once this set temperature

has been reached.

Turning a cylinder thermostat to a higher setting will not make the water heat up any faster. How quickly

the water heats up depends on the design of the heating system, for example, the size of boiler and

the heat exchanger inside the cylinder.

The water heating will not work if a time-switch or programmer has switched it off. And the cylinder

thermostat will not always switch the boiler off, because the boiler sometimes needs to heat the

radiators.

Cylinder thermostats are usually ﬁtted between one quarter and one third of the way up the cylinder.

The cylinder thermostat will have a temperature scale marked on it, and it should be set at between

60C and 65C, then left to do its job. This temperature is high enough to kill off harmful bacteria in the

water, but raising the temperature of the stored hot water any higher will result in wasted energy and

increase the risk of scalding.

Location

ST9120C

CS92A

(typically next to hot water cylinder, in bedroom)

This section is to be completed by the Installer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Honeywell Y9120W Sundial RF2 Pack 4 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info