Bedienungsanleitung Hoonved C 43 (Seite 14 von 19) (Englisch)

637642

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

4. Press the button (1) to automatically begin filling the

washing tank. Light (4) will come on once the level has

been reached. The water inside the boiler (see light 6)

and the water in the washing tank will automatically

start heating.

5. Open the door and pour the quantity of detergent

indicated by the manufacturer directly into the tub. This

operation need not be carried out when the machine is

equipped with the optional dispenser.

6. After warning light (6) has gone out, wait about 20

minutes to allow the water in the washing tub to reach

the programmed operating temperature.

3.3.b Washing operation (Figs 9-10)

1. Load the dirty crockery into the basket according to the

configuration of the machine.

2. Open the door and fit the basket into the tub, then shut

the door again.

3. Press “START” button (3). Light (5) will come on to

indicate that the cycle has started.

4. Light (5) will go out to indicate that the cycle has

terminated. Now open the door and remove the basket.

5. Add a spoonful of detergent after every 5/6 washes.

This operation need not be carried out if the machine

is equipped with the optional dispenser.

The doses are indicative and not binding since they

vary according to the hardness of the water and utilized

type of detergent.

Cold rinse - Optional - (only for C 35 -SPB 35 Mod.)

The coolthe glasses, at the end of the cycle, press for a few

seconds the cold rinse button (7) Fig. 1/9.

IMPORTANT

The hot water supply (50°÷60°C) does not allow a manual

cold rinse to be obtained.

IMPORTANT

Keep the tub door closed between one cycle and the next

to prevent the water in the tub from cooling.

ATTENTION

Door opening during the cycle will block machine operation

in the same way as an EMERGENCY device.

To interrupt the cycle, open the tub door in the following

way:

• Slightly open the tub door. Wait a few seconds for the

water pressure in the rods to drop, then completely

open the door.

• This operation is very important since it prevents the

operator from being wetted or scalded as during the

rinsing phase, the water reaches a temperature of

90°C.

• Close the door and the cycle will continue from where

it was interrupted.

3.3.c Changing the water (Fig. 10)

This operation must be carried out after every 10 cycles or

so, depending on the amount of accumulated dirt.

1. Switch off the machine as indicated in paragraph 3.3.d,

then lift the overflow (21) and allow the tub to completely

drain.

2. Fit the overflow (21) back into its housing and repeat

the machine preparation operations as indicated in

paragraph 3.3.a.

3.3.d Daily regenerating operations (for mod. CD-

CRD-SPD-SPRD only)(Fig. 10)

The regenerating operations must be carried out once

work has terminated.

1. Remove the overflow (21) and reset the line button (1).

2. Keep button (2) depressed for a few seconds. Warning

light (5) will come on to indicate the beginning of the

regenerating cycle, which lasts about 20 minutes.

ATTENTION

Remember to keep the door closed during the

regenerating phase.

3.3.e Manual drain (Fig. 1)

(on machine with drain pump only)

To manually empty the water from the tub, switch off the

line button (1) Fig. 1 and push the START/DRAIN button

(3).

3.3.f Switch-off (Fig. 9)

At the end of the work day, set the line switch (1) to position

“0” OFF, disconnect the main switch installed prior to the

machine and turn off the water delivery cock.

ATTENTION

Disconnect the main circuit-breaker prior to the machine

and turn off the water delivery cocks if the dishwasher is

faulty or operates badly.

Only allow technicians from the manufacturer’s authorized

after-sales service center to make repairs.

4. CLEANING (Fig. 10)

4.1 General information

Strict compliance with the maintenance instructions in this

section will keep your machine in a good working condition

and will notably reduce the need for repairs.

ATTENTION

If any machine component becomes faulty, FIRST CHECK

that all the instructions given in the previous paragraphs

have been complied with during use.

Repairs must be carried out immediately, as soon as the

fault occurs. This will prevent the trouble from becoming

worse and damaging other parts.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoonved C 43 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hoonved C 43

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info