Bedienungsanleitung Hoonved DP 50E (Seite 13 von 20) (Englisch)

637681

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

Part 2: For the operator

2.1.e.1Manual draining for mach. with drainage pump

For machines tted with a drainage pump it is possible

to empty the tank by carrying out the manual draining

cycle, during which only the drainage pump remains

active.

IMPORTANT

This cycle can only be carried out by leaving the ma-

chine SWITCHED ON with the tank full of water and the

door OPEN.

Having released the overow, press and hold the

START (S3) button until the LED LC2 and CHECK

together) begins to FLASH, and then release the

START (S3) button;

The DRAINAGE CYCLE will begin.

IMPORTANT

By pressing the START (ST) button or switching

the power switch (Q1) to OFF, you can interrupt the

drainage cycle before the preset time is up;

to restart the interrupted cycle, press START (S3)

again.

When the LC2 LED lights up CONSTANTLY,

the drainage cycle is nished.

At the end of the cycle, restore the lters (22/23) and the

overow (21) to their respective positions.

2.1.f Self-washing and draining

At the end of the washing operations SWITCH OFF the

machine pressing the switch (Q1)

After having unlocked the overow pipe, close the door

of tank access , press push button START (S3) (about

5 sec.)

The cycle Self-washing and draining will start ; Led LC1

and LC3 will light, while led CHECK is FIXED ON, with

draining pump ON (for the machines equipped with).

The end of the described phase is indicated by the switch-

ing OFF of the Led CHECK,

2.1.g Cold rinsing (optional)

With machine ON (switch line Q1 is ON ), tank full of

water and door closed (LC1 or LC2 or LC3 and CHECK

= FIXED ON)

keep pressed regeneration button (S4) to make the cold

rinsing of the crockeries for all the wished time.”

2.1.h Switching off at the end of the day

At the end of the working day SWITCH OFF the ma-

chine by pressing the power switch (Q1) into the

OFF position.

Switch off the mains switch feeding the machine

and close the water supply taps.

For any repairs, contact only assistance centres au-

thorised by the manufacturer.

Warnings during the operation

1) Ensure that the washing temperature remains at

approx. 55-60°C;

2) Avoid immersing bare hands in the detergent-lled

water; if this should happen, rinse immediately and

thoroughly with running water;

3) Use only anti-foaming detergents, specics for use in

industrial machines;

4) Deactivate the machine in case of break-down or

malfunction.

For any repairs, contact only assistance centres autho-

rised by the manufacturer, and insist on the use of

original parts.

5) In no case should you change the the original for-

mulations without rst consulting an authorised

assistance centre;

6) When the machine is operating, do not open the door

too rapidly.

7) Wash tank water should be changed at least twice a

day or according to daily wash requirements.

Failure to follow the above warnings may compromise

the safety of the washing machine.

Useful advice for better washibg results

Any unsatisfactory results from washing can be seen

when traces of dirt are left on dishes or other items; any

water marks may be caused by insufcient rinsing.

In this case, ensure that the rinsing nozzles (27) are

clean and that there is pressure in the water system.

If there are traces of waste, ensure that:

- The lters (22/23) are clean;

- the water temperature is around 55-60°C;

- items are correctly positioned in the basket;

- the washing/rinsing nozzles are clean (26/27);

- the arms (24/25) rotate freely.

2.1.i RESIN REGENERATION OPERATION

(for model D only)

We recommend that you carry out regeneration when all

work is nished.

First of all, ensure that there is coarse cooking salt in the

salt container, and proceed as follows:

1. unscrew the salt container plug and pour in 1 Kg of

coarse salt.

2.Screw the plug down tight, to ensure that the container

is completely sealed.

On reaching the set number of cycles, the CHECK LED

will ash;

this indicates that it is time to carry out regeneration.

The signal that the set number of cycles has been reached

can only be deactivated by starting the regeneration cycle

(regenerate button (S4)).

REGENERATION OPERATIONS

With the machine SWITCHED OFF (the power switch

(Q1) in the OFF position), and the tank EMPTY (release

the overow) and the door CLOSED, press and hold the

regenerate button (S4) (Fig. 1/ 9), until the CHECK LED

FLASHES.

The REGENERATION CYCLE will begin, and the

CHECK LED will ash continuously.

The machine will now automatically carry out all the ne-

cessary operations for a MAXIMUM of 20 mins, during

which the machine cannot be used.

ATTENTION

Opening the door during the cycle will stop the regenera-

tion cycle; the CHECK LED will start to ash RAPIDLY;

on closing the door the cycle will resume from where it

was stopped.

C I II III

LC1LC2LC3

CHECK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoonved DP 50E Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hoonved DP 50E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info