Bedienungsanleitung Hoonved ST 48E (Seite 12 von 20) (Englisch)

637675

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Part 1: General description and Safety devices

ENGLISH

Part 2: For the operator

2.1 WASHING PHASES ST/DP E

2.1.a Switching on and Preparing the machine

(Fig.1/9)

To switch on the machine,press and hold the power switch

(Q1) into the ON position button for a few seconds, then

release.

The LED indicating the last cycle selected will become

CONSTANTLY LIT (LC1, LC2, LC3 or LC1+LC2+LC3)

, as will the CHECK LED .

IMPORTANT

On rst switching on, LED LC2 will light up.

The boiler, and then the tank, will start to ll automatically.

Once the water level has been reached, the heating

elements will switch in, rst in the boiler, then in the tank.

Once the water in the tank reaches the correct tempera-

ture, the tank temperature LED (LTV) will go ON.

The thermometers P3 and P2 reect the tank and boiler

values of temperature.

WASHING OPERATION

If not equipped with an automatic dosing system, pour

into the tank a quantity of detergent suitable for the volu

me and hardness of the water. For quantities, refer to the

specic instructions for the detergent in use.

ATTENTION

When items to be washed are encrusted with burnt

on matter, or a long time has passed between use

and washing, it is essential to carry out a pre-was

soak using a suitable softening agent.

The use of hand-washing products is to be avoided

as they could produce foam inside the machine.

IPlace the basket of items to be washed inside the ma-

chine, having rst removed any solid waste.

2.1.b Selecting a Cycle

The duration of the washing cycle can be chosen from

4 different lengths of time, to be selected using the

“CYCLE” button.

Each time the “CYCLE” button is pressed, the LEDs

(LC1, LC2,LC3 or LC1+LC2+LC3), will light up or go out

in sequence as shown in the following table:

LC 1: SHORT CYCLE = 90 sec.

LC 2: MEDIUM CYCLE = 120 sec.

LC 3: LONG CYCLE = 180 sec.

LC 1+LC2+LC3: INTENSIVE CYCLE = 8 1/2 min.

2.1.c STARTING UP THE WASHING CYCLE

IMPORTANT

The selection of MANUAL orAUTOMATIC start to be

made with machine in stand-by mode

STARTING the MANUAL WASHING CYCLE

To start the washing cycle, press and hold the START (S3)

button for a few seconds, then release.

Throughout the washing cycle the LED(s) for the selected

cycle (LC1, LC2 or LC3 or LC1+LC2+LC3) will FLASH.

ATTENTION

We recommend that you top up the detergent used up

by washing grease or dispersed during rinsing every 4-5

complete cycles.

The use of the machine ensures rinsing at the ideal tem-

perature for hygienic purposes every time;

Indeed, if the temperature is not sufcient the wash will

be automatically prolonged so as to ensure the necessary

conditions of optimum rinsing at 85°C.

The waiting time required to attain optimum temperature

can extend to a maximum of 8 minutes.

While this is taking place, the CHECK LED will FLASH

RAPIDLY until the end of the cycle. To reset the ashing,

switch the machine off and back on using the power

switch (Q1) .

STARTINGUPTHEWASH. CYCLEAUTOMATICALLY

To start up the cycle AUTOMATICALLY (by opening and

closing the door), you will need to change the cycle start

up mode. Press and hold the “CYCLE” button until the

pre-selected cycle LED remains BLINKING LIT

(approx. 10 sec.) and the washing cycle will then start up

AUTOMATICALLY when the door is closed.

The functioning of the led (CONTINUOUS or BLINKING)

depends on the chosen type of functioning(MAN. or AUT)

2.1.d Interrupting the cycle

1) It is possible to interrupt the washing cycle momentarily

by opening the door, this is an EMERGENCY measure:

the cycle LEDs (LC1, LC2,LC3 or or LC1+LC2+LC3) will

start to FLASH, alternating with the CHECK LED .

On closing the door, operations will resume from the point

in which they stopped.

2) The cycle can also be interrupted by SWITCHING the

machine’s power switch (Q1) to the OFF position.

3) On switching the machine back on, the LED indicating

the last cycle selected will light up.

At the end of the washing cycle, take out the basket

and shake it gently so as to remove the last drops

left on the washed items.

Allow items to dry and remove them from the basket with

clean hands.

Store all items on hygienic and completely stable surfaces.

2.1.e Manual Draining

It is possible to drain the water from the tank at any time

during the day, according to the waste accumulated.

To carry out this operation, proceed as follows:

- SWITCH the machine’s power switch (Q1) to the OFF

position and release the overow, allowing all the water

to drain from the tank;

- Remove the tank lters (22/23) and clean;

I II III

LC1LC2LC3

CHECK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoonved ST 48E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hoonved ST 48E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info