Bedienungsanleitung Hoover Capture CP10 (Seite 4 von 61) (Alle Sprachen)

594363

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

GETTING TO KNOW YOUR CLEANER

ASSEMBLING YOUR CLEANER

Remove all components from the packaging.

1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To

release: simply press the two buttons on the hose end and pull [2].

2. Connect the tube upper end to the handle. [3].

3. Connect the tube lower end to the carpet and oor nozzle [4].

USING YOUR CLEANER

CLEANER MAINTENANCE

Replacing The Dust Bag

If the bag check indicator is red please check and, if necessary, replace the bag.

1. Lift the bag door release latch [13] to open the cover, pull the bag holder [14] and pull the

bag collar to remove the bag [15].

2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust bag

should be disposed of correctly and carefully.

3. Fold a new bag as shown on the bag and t by inserting the collar into the bag holder.

4. Ret the bag holder and close the bag door.

Warning - The bag door will NOT close if the dust bag and/or the bag holder are not assembled

to the cleaner. Always ensure the bag and bag holder are present when closing the bag door.

Remember: The bag check indicator may also be red if an obstruction has occurred. In this

case refer to ‘Removing A Blockage From the System’.

Cleaning the Filters

To maintain optimum performance of your cleaner, please wash the lters after each 5 bag changes.

Cleaning the pre-motor lter:

1. Lift the bag door release latch [13] to open the cover and remove the bag holder.

2. To remove the pre-motor lter slide the pre-motor lter frame from the cleaner. [16]

3. Remove the lter from the holder. [17]

4. Wash it in hand warm water, [20] and allow it to dry thoroughly before replacing to the

cleaner [21].

Cleaning the exhaust lter:

To remove the exhaust lter, unclip the exhaust lter cover [18] and remove the lter pack. [19]

2. Wash the lter in hand warm water [20] and allow it to dry thoroughly before replacing to

the cleaner. [21].

Remember: Do not use hot water or detergents. In the unlikely event of the lters becoming

damaged, t a Genuine Hoover replacement. Do not try and use the product without a dust

bag or lter tted.

Cleaning the permanent cloth dust bag*

To maintain optimum performance we recommend that you wash the permanent cloth dust

bag under hand warm water after every 5 full bags. Remove excess water and leave to dry fully

before replacing.

1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the red

marker [5].

2. Adjust the length of the telescopic tube* by moving the telescopic release button* up and

raise or lower the handle to the most comfortable cleaning position [6].

3. Carpet & Floor Nozzle. Press the pedal on the nozzle [7] to select the ideal cleaning mode

for the oor type.

Hard Floor: The brushes are lowered to protect the oor

Carpet: With lifted brushes for the deepest clean

4. Switch the cleaner on by pressing the On/O pedal on the cleaner main body. [8]

5. Adjust the power level by rotating the variable power control roller*. [9]

6. Adjust the suction regulator* to the desired level. [10].

7. Switch o at the end of use by pressing the On/O pedal. Unplug and press the cord rewind

pedal to wind the power cord back into the cleaner [11].

8. Parking and Storage - The tube can be parked for temporary storage while in use, or in the

storage position when not in use [12].

*Certain Models Only ** Certain models only, nozzles may vary according to model

A. Main Cleaner

B. Cord Rewind Pedal

C. Carry Handle

D. Exhaust Filter Cover

E. On/O Pedal

F. Telescopic Tube*

G. Telescopic Tube Release Button*

H. Standard Tube*

I. Variable Power Control Roller*

J. Bag Check Indicator

K. Bag Door Release Latch

L. Suction Regulator*

M. Handle

N. Carpet and Floor nozzle(GP)**

O. Surface selector Peda **

P. Hose

Q. Pre motor lter

R. Exhaust lter

S. 2 in 1 Tool

T. Pet Hair Remover Mini Turbo Nozzle*

U. Allergen Remover Mini Turbo Nozzle*

V. Grand Turbo Nozzle*

W. Parquet nozzle*

N1. Carpet Nozzle (CA)**

N2. Hard Floor Nozzle (HF)**

Removing a Blockage From The System

If the bag check indicator is illuminated or ashing:

1. Check if the bag is full. If so refer to ‘Replacing The Dust Bag’.

2. If it is not full, then;

A. Do the lters need cleaning? If so refer to ‘Cleaning the Filter’.

B. Check if there is any other blockage in the system - Use a rod or a pole to remove any

blockage from the Teletube or exible hose.

Warning - The bag check indicator will turn red if the cleaner is used when full, if there is a

blockage or if the lters are dirty. If the cleaner is used for a signicant period of time with the

bag check indicator is red, a thermal cut out will switch the cleaner o to prevent overheating.

The bag check indicator turn green once the cleaner has switched o to signal that the thermal

cut out has been activated. If this should happen, switch the cleaner o, unplug and correct the

fault. It will take about 30 minutes for the cut out to automatically reset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover Capture CP10 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info