Bedienungsanleitung Hoover Classic FloorMate (Seite 10 von 48) (Englisch)

594407

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

RECOMMENDED CLEANING SEQUENCE

Use your HOOVER

FloorMate™ SpinScrub

Cleaner to:

• VACUUM: Vacuum to remove loose dirt, hair and debris.

• WASH: Clean the floor surface. The brushes will provide light agitation to

help loosen dirt.

• DRY: Pickup reduces drying time of the floor surface.

The Mode selector dial turns the brushes on and off.

3.1 For dry debris pickup, turn the dial to the VACUUM position. In this position,

the brushes will not rotate and are raised off the floor surface.

To wet clean with brushes turned ON, turn the dial to the WASH position.

For wet pickup, turn the dial to the DRY position.

3. HOW TO CLEAN

CLEANING FLOORS

If using cleaner on sealed wood floors, inspect floor

surface for worn finish, bare wood or separated

joints. Do not use FloorMate™ SpinScrub

cleaner

to wet clean sealed wood floors if any of these

conditions exist.

Set Mode selector dial to VACUUM position and

vacuum floor.

Turn cleaner off and disconnect from electrical

outlet. Empty Dirty Water Tank (see Figs. 2.15 &

2.16).

Fill Clean Water Solution Tank with either Floor to

Floor Cleaning Concentrate or Grout Cleaner,

depending upon the type of floor being cleaned, and

water (see Figs. 2.8 through 2.14).

Do not use solvent based cleaning concentrates in

your cleaner. Do not use any type of wax in your

cleaner.

Turn Mode selector dial to WASH position.

Dry hands and plug cleaner into a properly grounded

outlet.

Step on handle release pedal and lower handle to

operating position. Turn cleaner ON.

3.2 To release solution, squeeze trigger (A). Slowly

move cleaner forward and backward over area to

be cleaned.

Squeeze trigger to release solution as needed.

Overlap strokes by one inch to help prevent

streaking. The cleaner’s suction will pick up the dirty

solution throughout cleaning.

To greatly enhance drying of the floor surface,

release trigger and turn Mode selector dial to the

DRY position. Continue to move cleaner over the

area to pick up the dirty solution.

IMPORTANT

Your HOOVER

FloorMate™ SpinScrub

cleaner may be used to clean wood floors that

have been sealed with a polyurethane coating

and can be cleaned with water.

When cleaning sealed wood floors, make sure

all areas are completely dry. Ensure that no

water remains on the floor.

When switching between wet cleaning and wet

pickup, it is not necessary to turn the cleaner off.

Simply move the Mode selector dial between

the two settings.

CAUTION

! !

To prevent damage to wood floors, follow

the flooring manufacturer’s cleaning

recommendations.

To continue cleaning another area, turn Mode

selector dial to WASH position. Repeat cleaning

motion.

Empty Dirty Water Tank or clean the filter when the

motor sound becomes higher in pitch and there is a

loss of suction (see “Automatic shut-off” section).

3.2

3.1

VACUUM

WASH

DRY

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover Classic FloorMate Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info