Bedienungsanleitung Hoover DDY 062B (Seite 23 von 32) (Englisch)

594554

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

If a 9 hour delay is set, countdown will be

displayed by the 6h indicator light after 3

hours and the 3h indicator light after 6

hours.

At the end of the last 3 hours (at the end

of countdown) the 3h indicator light will

stop flashing and remain on to indicate the

washing phase and the programme will

start automatically.

If countdown has not ended, whereby

the programme has not yet started, it is

possible to change or cancel the delayed

start and select another programme or to

select/deselect the option button, proceeding

as follows:

■ Hold the "RESET" button down for at

least 5 seconds.

The programme indicator lights will flash

and some audible signals will sound.

■ The delayed start and the selected

programme will be cancelled. The indicator

light for the “recommended” programme

will start to flash.

■ Press the "DELAY START" button to

set another delayed start time (the

corresponding indicator light will turn on).

■ A new programme can be set after a

delayed time has been changed or

cancelled or an option button can be

selected or deselected.

Alarm mute for the PROGRAMME

END

The alarm for the programme end may be

muted as follows:

IMPORTANT

The dishwasher must be ALWAYS off

before start this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 15 seconds

(during this time, 2 audible signals will

sound).

3. Release the button when the second

audible signal sounds (3 "PROGRAMME

SELECTION" indicator lights will come

on).

4. Press the same button again: the 3

indicator lights (which indicate that the

alarm is activated) will start flashing (to

indicate that the alarm is off).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To turn the alarm on again, follow the same

procedure.

Fault signals

If malfunctions or faults occur when a

programme is running the indicator light

that corresponds to the selected cycle

will flash rapidly and the alarm sounds.

In this event, turn the dishwasher off by

pressing the "ON/OFF" button.

After checking to make sure the water

inlet hose tap is open, that the drain

hose is not bent and that the siphon or

filters are not clogged, set the selected

programme again.

If the anomaly persists, contact Customer

Service Department.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically discharge any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, we

recommend that the dishwasher is

not moved or tilted during operation.

If however it is necessary to tilt or

move the dishwasher, please ensure

that the washing cycle is complete

and that there is no remaining water

inside the dishwasher.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover DDY 062B Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info