Bedienungsanleitung Hoover HAHG6 (Seite 10 von 98) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

817768

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

1. As illustrated, assemble parts in sequence:

2. Tighten the joints with the spanner, remembering

to twist the pipes into position.

IMPORTANT: carry out a ﬁnal check for leaks on

the pipe connections using a soapy solution.

For some models a conic link is furnished to

outﬁt for the installation in the countries where

this type of link is obligatory; in picture 8 it is

pointed out how to recognize the diﬀerent

types of links (CY = cylindrical, CO = conic). In

every case the cylindrical part of the link has to

be connected to the hob.

The ﬂexible tube shall be ﬁtted in such a way that

it cannot come into contact with a moveable

part of the housing unit (e.g. a drawer) and does

not pass through any space where it may

become crushed/ kinked or damaged in any

way.

B: 1/2 Seal

A: 1/2 Male Adaptor Cylindirical

C: 1/2 Female Gas Adaptor Conical-Cylindirical

3. Attach ﬁtting C to mains gas supply using rigid

copper pipe or ﬂexible steel pipe.

When connecting the hob to the gas supply via

use oﬄexible hoses please ensure that the

maximum distance covered by the hose does

not exceed 2 metres.

To prevent any potential damage to the hob

please carry out the installation following this

sequence (Figure 6*):

or Cylindirical-Cylindirical

NEVER USE A FLAME. Also, make sure that the

ﬂexible pipe cannot come into contact with a

moving part of the cabinet (eg.adrawer) and that

it is not situated where it could be damaged.

Warning: If gas can be smelt in the vicinity of this

appliance turn oﬀ the gas supply to the

appliance and call the engineer directly. Do not

search for a leak with a naked ﬂame.

ADAPTING THE HOB TO DIFFERENT TYPE

OF GAS

To adapt the Hob for use with diﬀerent types of

gas, carry out the following instructions:

• Remove the grids and burners

• Unscrew the injector and replace it with one

suitable for the gas to be used (see gas type

table)

burner support (Figure 7*)

• Insert on hexagonal spanner (7 mm) into the

REGULATING THE MINIMUM FLAME

After lighting the burners, turn the control knob

to the minimum setting and then remove the

knob (this can easily be removed by applying

gentle pressure).

Turning the screw clockwise reduces the gas

ﬂow, whilst turning it anticlockwise increases

the ﬂow – Use this adjustment to obtain a ﬂame

of approximately 3 to 4 mm in length and then

replace the control knob.

Using a small «Terminal» type screwdriver the

regulating screw can be adjusted as in Figure 9*.

When the gas supply available is LPG - the

screw to set the idle ﬂame must be turned

(clockwise) to the end stop.

When you have carried out the new gas

regulation, replace the old gas rating plate on your

appliance with one (supplied with hob) suitable for

the type of gas for which it has been regulated.

*See “Technical information” section at the end of this manual.

EN 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover HAHG6 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info