Bedienungsanleitung Hoover HAVG5BF4S2B (Seite 9 von 178) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

817765

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

ADAPTING THE HOB TO DIFFERENT TYPE

OFGAS

B:1/2Seal

C:1/2 Female GasAdaptorConical-Cylindirical

1.Asillustrated,assemblepartsinsequence:

copperpipeorﬂexiblesteelpipe.

orCylindirical-Cylindirical

burnersupport(Figure7*)

•Unscrewtheinjectorandreplaceitwithone

When connecting the hob to the gas supply via

use oﬄexible hoses please ensure that the

maximum distance covered by the hose does

notexceed2metres.

A:1/2MaleAdaptorCylindirical

For some models a conic link is furnished to

outﬁt for the installation in the countries where

this type of link is obligatory; in picture 8 it is

pointed out how to recognize the diﬀerent

types of links (CY = cylindrical, CO = conic). In

every case the cylindrical part of the link has to

beconnectedtothehob.

NEVER USE A FLAME. Also, make sure that the

ﬂexible pipe cannot come into contact with a

movingpart of the cabinet (eg.adrawer)and that

itisnotsituatedwhere itcouldbe damaged.

IMPORTANT: carry out a ﬁnal check for leaks on

thepipeconnectionsusingasoapysolution.

table)

2. Tighten the joints with the spanner, remembering

To prevent any potential damage to the hob

please carry out the installation following this

sequence(Figure6*):

Warning: If gas canbe smeltin the vicinityof this

appliance turn oﬀ the gas supply to the

appliance and call the engineer directly. Do not

searchforaleakwithanakedﬂame.

to twist the pipes into position.

3.AttachﬁttingCtomainsgassupplyusingrigid

•Removethe gridsandburners

Theﬂexibletubeshallbeﬁttedinsuchawaythat

it cannot come into contact with a moveable

part of the housing unit (e.g. a drawer) and does

not pass through any space where it may

become crushed/ kinked or damaged in any

way.

To adapt the Hob for use with diﬀerent types of

gas,carryout thefollowinginstructions:

suitableforthegastobeused(seegastype

•Insertonhexagonalspanner(7mm)intothe

Using a small «Terminal» type screwdriver the

regulatingscrewcanbeadjustedasinFigure 9*.

Turning the screw clockwise reduces the gas

ﬂow, whilst turning it anticlockwise increases

the ﬂow – Use this adjustment to obtain a ﬂame

of approximately 3 to 4 mm in length and then

replacethecontrolknob.

When you have carried out the new gas

regulation,replace theold gas ratingplate on your

appliance with one (supplied with hob) suitable for

thetypeof gas forwhich it has been regulated.

After lighting the burners, turn the control knob

to the minimum setting and then remove the

knob (this can easily be removed by applying

gentlepressure).

REGULATINGTHEMINIMUMFLAME

When the gas supply available is LPG - the

screw to set the idle ﬂame must be turned

(clockwise)tothe endstop.

*See“Technical information”sectionat theendof thismanual.

EN 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover HAVG5BF4S2B Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info