Bedienungsanleitung Hoover HFI 303D (Seite 12 von 17) (Englisch)

594580

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Programme operations

When a programme is running the relevant

indicator light will remain on and the 3

“PROGRAMME STATUS” indicator lights

("WASH" , "RINSE" , and "DRY" )

will light singularly and in sequence to

indicate the current phase.

If there is any break in the power supply

while the dishwasher is operating, a

special memory stores the selected

programme and, when the power is

restored, it continues where it left off.

Programme end

A 5 second alarm will sound (if not muted)

3 times at 30 second intervals to signal that

the programme has ended.

The selected programme indicator light (2

indicator lights for the "COLD RINSE"

programme) will start to flash.

Dishes can now be removed and the

dishwasher turned off by pressing the

"ON/OFF" button or dishes can be loaded

for new cycle.

Option button

"1/2 AUTO" button

In response to your everyday washing

requirement in addition to the normal wash

functions this dishwasher is equipped with

the “1/2 AUTO” function. This function

enables the uses to wash a reduced

number of dishes yet retaining the freedom

of loading them both on the top and bottom

basket.

When this function is activated the dishwasher

will automatically reduce the water and

energy consumption and the wash time.

When selecting the “1/2 AUTO” ensure a

reduced amount of detergent is used.

"DELAY START" button

The dishwasher start time can be set with

this button, delaying the start by 3, 6 or 9

hours.

Proceed as follows to set a delayed start:

■ Press the "DELAY START" button (each

time the button is pressed the start

will be delayed by 3, 6 or 9 hours

respectively and the corresponding time

indicator light will illuminate).

■ To start the countdown, press the selected

programme button (the relevant indicator

light will come on, while the set time

indicator light will start to flash).

If a 9 hour delay is set, countdown will be

displayed by the 6h indicator light after 3

hours and the 3h indicator light after 6

hours.

At the end of the last 3 hours (at the end

of countdown) the 3h indicator light will

stop flashing and remain on to indicate the

washing phase and the programme will

start automatically.

If countdown has not ended, whereby

the programme has not yet started, it is

possible to change or cancel the delayed

start and select another programme or to

select/deselect the option button, proceeding

as follows:

■ Hold down the selected programme

button for at least 5 seconds.The

programme indicator lights will flash and

some audible signals will sound.

■ The delayed start and the selected

programme will be cancelled. The indicator

light for the “recommended” programme

will start to flash.

■ Press the "DELAY START" button to

set another delayed start time (the

corresponding indicator light will turn on).

■ A new programme can be set after a

delayed time has been changed or

cancelled or an option button has selected

or deselected.

Alarm mute for the PROGRAMME

END

The alarm for the programme end may be

muted as follows:

IMPORTANT

The dishwasher must be ALWAYS off

before start this procedure.

1. Hold down the FIRST "PROGRAMME"

button (from the right) and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME" button pressed

for at least 15 seconds (during this time,

2 audible signals will sound).

3. Release the button when the second

audible signal sounds (3 "PROGRAMME

SELECTION" indicator lights will come

on).

4. Press the same button again: the 3

indicator lights (which indicate that the

alarm is activated) will start flashing (to

indicate that the alarm is off).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To turn the alarm on again, follow the same

procedure.

Fault signals

If malfunctions or faults occur when a

programme is running the indicator light

that corresponds to the selected cycle

(2 indicator lights for the "COLD RINSE"

programme) will flash rapidly and the alarm

sounds.

In this event, turn the dishwasher off by

pressing the "ON/OFF" button.

After checking to make sure the water

inlet hose tap is open, that the drain

hose is not bent and that the siphon or

filters are not clogged, set the selected

programme again.

If the anomaly persists, contact Customer

Service Department.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically discharge any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, we

recommend that the dishwasher is

not moved or tilted during operation.

If however it is necessary to tilt or

move the dishwasher, please ensure

that the washing cycle is complete

and that there is no remaining water

inside the dishwasher.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover HFI 303D Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info