22
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme operations
When a programme is running the relevant
indicator light will remain on and the 3
“PROGRAMME STATUS” indicator lights
("WASH", "RINSE", and "DRY") will light
singularly and in sequence to indicate the
current phase.
Programme end
A5 second alarm will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended.
The “PROGRAMME STATUS” indicator
lights will turn off and the selected
programme indicator light (for the "PRE-
RINSE" programme, only the option button
indicator light) will start to flash.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for new cycle.
Option button
“5 IN 1” button
This option optimises the use of “3 in 1”/
“4 in 1”/“5 in 1” combined detergents. By
pressing this button, the selected washing
programme is modified to get the best
performance from combined detergents.
WARNING!
Before starting any wash using
combined detergents "3 in 1" / "4 in 1" /
"5 in 1", please ALWAYS remember
to press this button.
When this option is selected, the salt
light might switch on. The refill of the
salt container (and rinse aid container
too) is required ONLY in case of
return to the use of conventional
detergents.
Anyway you are recommended to
read information included in the
paragraph "3 in 1" / "4 in 1" / "5 in 1"
combined detergents of section
"TYPES OF DETERGENTS".
IMPORTANT
When this option is selected, the
"RAPID" cycle is 10 minutes longer.
"DELAY START" button
The dishwasher start time can be set with
this button, delaying the start by 3, 6 or 9
hours.
Proceed as follows to set a delayed start:
■ Press the "DELAY START" button (each
time the button is pressed the start
will be delayed by 3, 6 or 9 hours
respectively and the corresponding time
indicator light will illuminate).
■ To start the countdown, press the selected
programme button (the relevant indicator
light will come on, while the set time
indicator light will start to flash).
If a 9 hour delay is set, countdown will be
displayed by the 6h indicator light after 3
hours and the 3h indicator light after 6
hours.
At the end of the last 3 hours (at the end
of countdown) the 3h indicator light will
stop flashing and remain on to indicate the
washing phase and the programme will
start automatically.
If countdown has not ended, whereby
the programme has not yet started, it is
possible to change or cancel the delayed
start and select another programme or to
select/deselect the option button, proceeding
as follows:
■ Hold down the selected programme
button for at least 5 seconds. The
programme indicator lights (except for
the "RAPID" programme indicator light)
will flash.
■ The selected programme will be cancelled
and the indicator light for the
"recommended" programme will start
to flash.
23
■ Press the "DELAY START" button to
set another delayed start time (the
corresponding indicator light will turn on).
■ A new programme can be set after a
delayed time has been changed or
cancelled or an option button has selected
or deselected.
Alarm mute for the PROGRAMME
END
The alarm for the programme end may be
muted as follows:
■ With the dishwasher off, hold down the
"5 IN 1" button for few seconds while
simultaneously pushing the "ON/OFF"
button, releasing them only after the
alarm sound.
■ Press the "5 IN 1" button again: the
relevant indicator light (turned on to
indicate that the alarm is activated) will
flash (to indicate that the alarm is off).
■ Wait for the alarm to sound to indicate
that the settings were saved.
■ To turn the alarm on again, follow the
same procedure.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(for the "PRE-RINSE" programme, only
the option button indicator light) will flash
rapidly and the alarm sounds.
In this event, turn the dishwasher off by
pressing the "ON/OFF" button.
After checking to make sure the water
inlet hose tap is open, that the drain
hose is not bent and that the siphon or
filters are not clogged, set the selected
programme again.
If the anomaly persists, contact Customer
Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
