Bedienungsanleitung Horizon Fitness Adventure 4 Plus (Seite 9 von 11) (Englisch)

641017

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

16 17

DO NOT stand on running belt while calibrating – stand on

the side rails. The treadmill will fluctuate between low and

high speeds for several minutes until calibration is complete.

WARNING

TROUBLESHOOTING HEART RATE

(GRIP-PULSE ONLY)

Check your exercise environment for sources of

interference such as fluorescent lights, computers,

underground fencing, home security systems or appliances

containing large motors. These items may cause erratic

heart rate readouts.

You may experience an erratic readout under the following

conditions:

• Gripping the heart rate handlebars too tight. Try to

maintain moderate pressure while holding onto the

heart rate handlebars.

• Constant movement and vibration due to constantly

holding the heart rate handlebars while exercising. If

you are receiving erratic heart rate readouts, try to only

hold the grips long enough to monitor your heart rate.

• When you are breathing heavily during a workout.

• When your hands are constricted by wearing a ring.

• When your hands are dry or cold. Try to moisten your

palms by rubbing them together to warm.

• Anyone with heavy arrhythmia.

• Anyone with arteriosclerosis or peripheral circulation

disorder.

• Anyone whose skin on the measuring palm is

especially thick.

PROBLEM: Operating speed appears inaccurate.

SOLUTION: Auto-calibrate the treadmill:

• Power on the treadmill and have the safety key in position on the

console. Press and hold the elevation “+” and speed “–” buttons

for approximately 5 seconds to enter the Engineering Mode. The

console will beep and “ENG0” appears in the display.

• Press the Speed “+” or “–” button until “ENG2” appears in the

display.

• Press, “ENTER” to select. Press, “START” to begin. The

treadmill running belt will begin to move automatically and the

auto-calibration sequence will properly set and store the speed

values.

• Upon successful calibration, the treadmill will beep several times.

The console will automatically exit Engineering Mode and return

to the start-up screen.

NOTE: Some treadmill models do not have auto-calibrate. Turn the

treadmill off and disconnect the power cord. Check the console

cable for pinches and make sure it is connected properly to both the

upper and lower boards.

TROUBLESHOOTING

If this troubleshooting section does not remedy the problem,

discontinue use and turn the power off.

PLEASE CALL YOUR LOCAL DEALER.

The following information may be asked of you when you call.

Please have these items readily available:

• Model Name

• Serial Number

• Date of Purchase (receipt or credit card statement)

In order for your local dealer to service your treadmill they may

need to ask detailed questions about the symptoms that are

occurring. Some troubleshooting questions that may be asked

are:

• How long has this problem been occurring?

• Does this problem occur with every use? With every user?

• If you are hearing a noise, does it come from the front or

the back? What kind of noise is it (thumping, grinding,

squeaking, chirping etc.)?

• Has the machine been lubricated and maintained per the

maintenance schedule?

Answering these and other questions will give the technicians

the ability to send proper replacement parts and the service

necessary to get you and your treadmill running again!

MAINTENANCE

Preventative maintenance is the key to smooth operating

equipment, as well as keeping the users liability to a minimum.

Equipment needs to be inspected at regular intervals. Defective

components must be replaced immediately. Improperly

working equipment must be kept out of use until it is repaired.

Ensure that any person(s) making adjustments or performing

maintenance or repair of any kind is qualified to do so.

AFTER EACH USE (DAILY)

Clean and inspect, following these steps:

• Turn off the treadmill with the ON/OFF switch, then unplug

the power cord at the wall outlet.

• Wipe down the running belt, deck, motor cover, and

console casing with a damp cloth. Never use solvents, as

they can cause damage to the treadmill.

• Inspect the power cord. If the power cord is damaged,

contact your local dealer.

• Make sure the power cord is not underneath the treadmill

or in any other area where it can become pinched or cut.

• Check the tension and alignment of the running belt.

Make sure that the treadmill belt will not damage any other

components on the treadmill by being misaligned.

EVERY WEEK

Clean underneath the treadmill, following these steps:

• Turn off the treadmill with the ON/OFF switch, then unplug

the power cord at the wall outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Horizon Fitness Adventure 4 Plus Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Horizon Fitness Adventure 4 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info