Bedienungsanleitung Horizon Fitness Elite T5000 (Seite 6 von 39) (Deutsch, Englisch, Holländisch, Französisch)

520067

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

1110

CENTERING THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped.

At times the belt can move off-center during shipment. Before operating the

treadmill, make sure the belt is centered and remains centered to maintain

smooth operation.

If the running belt is too far to the right side: With the treadmill running at 1

mph, turn the left adjustment bolt counter-clockwise ¼ turn at a time (using the

supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to

gauge if more adjustment is needed. Repeat if necessary, until the belt remains

centered during use.

If the running belt is too far to the left side: With the treadmill running at 1

mph or 1.6 kmh, turn the right adjustment bolt counter-clockwise ¼ turn at a time

(using the supplied Allen wrench). Check the belt alignment. Allow belt to run a

full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt

remains centered during use.

*NOTE: Folding, moving and leveling information might vary according to the model

you buy. Please see Owner’s manual for further information.

For centering the belt: For centering the belt you may refer to the marking dot

on motor cover to line-up the edge of the logo on belt.

Do not run belt faster than 1 mph or 1.6 kmh while centering. Keep fingers,

hair and clothing away from belt at all times.

CAUTION

BELT IS TOO FAR TO THE RIGHT SIDE

BELT IS TOO FAR TO THE LEFT SIDE

TENSIONING THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped.

At times the belt can move off-center during shipment.

Running belt should NOT be moving during tensioning. Over-tightening

the running belt can cause excessive wear on the treadmill as well as its

components. Never over-tighten the belt.

CAUTION

If you can feel a slipping sensation when running on the treadmill, the running

belt must be tightened. In most cases, the belt has stretched from use, causing

the belt to slip. This is a normal and common adjustment. To eliminate this

slipping, turn the treadmill off and tension both the rear roller bolts using

the supplied Allen wrench, turning them ¼ turn to the right as shown. Turn the

treadmill on and check for slipping. Repeat if necessary, but never turn the roller

bolts more than ¼ turn at a time. Belt is properly tensioned when the slipping

sensation is gone.

TIGHTENS RIGHT SIDE OF ROLLER

TIGHTENS LEFT SIDE OF ROLLER

LEVELING THE TREADMILL

Your treadmill should be leveled for optimum use. Once you have placed your

treadmill where you intend to use it, raise or lower one or both of the adjustable

levelers located on the bottom of the treadmill frame*. A carpenter’s level is

recommended. If your treadmill is not level, the running belt may not track

properly. Once you have leveled your treadmill, lock the levelers in place by

tightening the nuts against the frame (Some treadmills do not have levelers).

LOCK

ADJUSTMENT

ADJUST

HEIGHT

JHT14_GUIDE_TM_ID_Rev1_0.indd 10-11 7/13/15 3:40 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Horizon Fitness Elite T5000 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Horizon Fitness Elite T5000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info