Bedienungsanleitung Horizon Fitness Elite T5000 (Seite 9 von 39) (Deutsch, Englisch, Holländisch, Französisch)

520067

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

1716

DO NOT stand on running belt while calibrating – stand on

the side rails. The treadmill will fluctuate between low and

high speeds for several minutes until calibration is complete.

WARNING

TROUBLESHOOTING HEART RATE

(GRIP-PULSE ONLY)

Check your exercise environment for sources of

interference such as fluorescent lights, computers,

underground fencing, home security systems or

appliances containing large motors. These items may

cause erratic heart rate readouts.

You may experience an erratic readout under the

following conditions:

• Gripping the heart rate handlebars too tight. Try to

maintain moderate pressure while holding onto the

heart rate handlebars.

• Constant movement and vibration due to constantly

holding the heart rate handlebars while exercising.

If you are receiving erratic heart rate readouts, try

to only hold the grips long enough to monitor your

heart rate.

• When you are breathing heavily during a workout.

• When your hands are constricted by wearing a ring.

• When your hands are dry or cold. Try to moisten

your palms by rubbing them together to warm.

• Anyone with heavy arrhythmia.

• Anyone with arteriosclerosis or peripheral

circulation disorder.

• Anyone whose skin on the measuring palm is

especially thick.

PROBLEM: Operating speed appears inaccurate.

SOLUTION: Auto-calibrate the treadmill:

• Power on the treadmill and have the safety key in position on

the console. Press and hold the elevation “+” and speed “–”

buttons for approximately 5 seconds to enter the Engineering

Mode. The console will beep and “ENG0” appears in the

display.

• Press the Speed “+” or “–” button until “ENG2” appears in the

display.

• Press, “ENTER” to select. Press, “START” to begin. The treadmill

running belt will begin to move automatically and the auto-

calibration sequence will properly set and store the speed

values.

• Upon successful calibration, the treadmill will beep several

times. The console will automatically exit Engineering Mode

and return to the start-up screen.

NOTE: Some treadmill models do not have auto-calibrate. Turn the

treadmill off and disconnect the power cord. Check the console

cable for pinches and make sure it is connected properly to both

the upper and lower boards.

TROUBLESHOOTING

If this troubleshooting section does not remedy the problem,

discontinue use and turn the power off.

PLEASE CALL YOUR LOCAL DEALER.

The following information may be asked of you when you

call. Please have these items readily available:

• Model Name

• Serial Number

• Date of Purchase (receipt or credit card statement)

In order for your local dealer to service your treadmill they

may need to ask detailed questions about the symptoms that

are occurring. Some troubleshooting questions that may be

asked are:

• How long has this problem been occurring?

• Does this problem occur with every use? With every

user?

• If you are hearing a noise, does it come from the front

or the back? What kind of noise is it (thumping, grinding,

squeaking, chirping etc.)?

• Has the machine been lubricated and maintained per the

maintenance schedule?

Answering these and other questions will give the technicians

the ability to send proper replacement parts and the service

necessary to get you and your treadmill running again!

MAINTENANCE

Preventative maintenance is the key to smooth operating

equipment, as well as keeping the users liability to a

minimum. Equipment needs to be inspected at regular

intervals. Defective components must be replaced

immediately. Improperly working equipment must be kept

out of use until it is repaired. Ensure that any person(s)

making adjustments or performing maintenance or repair of

any kind is qualified to do so.

AFTER EACH USE (DAILY)

Clean and inspect, following these steps:

• Turn off the treadmill with the ON/OFF switch, then

unplug the power cord at the wall outlet.

• Wipe down the running belt, deck, motor cover, and

console casing with a damp cloth. Never use solvents, as

they can cause damage to the treadmill.

• Inspect the power cord. If the power cord is damaged,

contact your local dealer.

• Make sure the power cord is not underneath the

treadmill or in any other area where it can become

pinched or cut.

• Check the tension and alignment of the running belt.

Make sure that the treadmill belt will not damage any

other components on the treadmill by being misaligned.

EVERY WEEK

Clean underneath the treadmill, following these steps:

• Turn off the treadmill with the ON/OFF switch, then

unplug the power cord at the wall outlet.

JHT14_GUIDE_TM_ID_Rev1_0.indd 16-17 7/13/15 3:40 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Horizon Fitness Elite T5000 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Horizon Fitness Elite T5000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info