Bedienungsanleitung Hot Spring PRODIGY - H (Seite 22 von 48) (Englisch)

624653

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

HOME SCREEN

The temperature displayed in the

center of the Home screen is the

actual temperature of the spa water.

If the READY icon is lit and solid

on the screen, then the actual spa

temperature is within 2°F (1°C) of

the set temperature. The corner soft

button functions are as follows:

MEMORY

This feature will recall the last active setting for jets and lights prior to

pressing the All Off button.

IMPORTANT: If the jet pump will not engage, make sure SPA LOCK is

deactivated. SPA LOCK disables the controls on the control panel.

ALL OFF

This feature will shut all jets and lights off immediately, while saving the

last active jets and lights settings.

AUDIO

If you purchased music or TV accessories with your spa, this feature will

take you to the Audio menu.

CLEAN

Provided as a convenient timer for water maintenance, this function

activates the jet pump on high for a ten minute period. The jet icon (on

the Home Screen) will flash to indicate the jet pump is engaged and

in the clean cycle. Next you may add properly measured spa water

chemicals into the filter compartment. The jet pump and clean icon will

automatically shut off after ten minutes.

IMPORTANT: Some soft key functions will only be displayed if the

accessory has been installed.

TEMPERATURE CONTROL

The set temperature range is from 80°F

to 104°F (26°C to 40°C). (The water

temperature of any spa may rise or

lower slightly depending on the current

use and condition of your spa and on

outside temperatures.)

The set temperature of the spa water

will default to 100°F (38°C) the first

time that power is applied. This is

the setting programmed at the factory. After the spa has been set up

and used, the last temperature value set by the user will be stored in

memory. If power is disconnected from the spa, it will automatically revert

to the last set temperature when power is reapplied.

To display the set temperature of the spa:

• Press the OPTIONS hard button on the Control panel .

• Press the soft button next to Temperature. The set temperature

screen will be displayed. This screen will automatically revert to the

Home screen after 45 seconds of non-use.

To increase the set temperature of the spa water:

• Press the soft button next to ▲.

Each time the button is pressed,

the set temperature display will

increase by one degree. If the

button is held down, the set

temperature display will increase

by one degree every half-second.

To decrease the set temperature of the spa water:

• Press the soft button next to ▼.

Each time the button is pressed, the

set temperature

display will decrease

by one degree. If the button is held

down, the set temperature display will

decrease by one degree every half-

second.

If the set temperature value does not

change, check to see whether the

TEMP LOCK or SPA LOCK features are on. When either of these

features is activated, the temperature control is disabled.

The temperature can be displayed in Fahrenheit or Celsius. Press the

soft button next to the °F/°C to choose one or the other.

LOCKING FEATURES

The two locking features, Temperature Lock and Spa Lock, are

activated at the Control panel. Once activated, a lock will remain active

until the specific button combination is pressed to disable the lock. Even

if power to the spa is disconnected even briefly, the lock will remain

activated.

TEMPERATURE LOCK

When activated, the Temperature Lock

feature prevents a change in your

desired water temperature setting.

All other functions on the control

panel will operate normally while the

temperature lock is "ON". This feature

prevents others from changing the

owner's desired settings.

To activate the Temperature Lock:

• Press the OPTIONS hard button at the Control panel.

• Press the soft button next to Temperature to advance the screen.

• Press the soft button next to Temp Lock Off to change the screen to

Temp Lock On.

IMPORTANT: The Temperature/Spa lock icon will be displayed on the

Home Screen during a temperature lock condition.

To deactivate the Temperature Lock:

• Press the OPTIONS hard button at the Control panel.

• Press the soft button next to Temp Lock.

• Press the soft button next to Temp Lock On to change the screen to

Temp Lock Off to turn the Temp lock and icon off.

Page 19

Operating Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hot Spring PRODIGY - H Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info