Bedienungsanleitung Hot Spring SOVEREIGN - II (Seite 14 von 48) (Englisch)

624652

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Page 11

Water Quality and Maintenance

OZONE MAINTENANCE

Reduced or no ozone bubbles coming from heater return (clogged

ozone injector) or no ozone, clean the injector:

1. Place 16 ounces of white vinegar into a cup or bucket.

2. Carefully loosen the long tubing attached to the bottom of the

ozonator, located in the equipment compartment.

DANGER: Place the end of the tubing into the vinegar, making

certain that the end of the tubing sits at the bottom of the container.

3. Run the spa until all 16 ounces of the vinegar are gone. This should

allow

an ample flow of vinegar to be run through the injector and clear the

blockage.

4. Reinstall the tubing to the bottom of the ozonator.

Water chemistry damage is not covered by the warranty. The chemical

levels and water quality in the spa are under your direct control.

With proper basic care, the spa will provide many years of hot water

relaxation. If you are unsure about any chemical or its usage in the spa,

contact your Authorized Dealer, or Watkins Manufacturing Corporation.

DO:

• Add all chemicals slowly into the filter compartment with the jet pump

operating for ten minutes.

• Use special care if using baking soda to clean either the interior or

exterior plastic surfaces.

IMPORTANT: Watkins Manufacturing Corporation DOES NOT

recommend the use of any floating chemical dispenser. Damage to

the spa shell or components caused by a floating chemical dispenser

is specifically not covered under the terms of the limited warranty.

Floating dispensers can become trapped in one area and cause an

over-sanitization or release large chunks of sanitizer that very quickly

chemically burns the shell and cover.

DON'T:

• Use compressed sanitizers.

• Use a floater type sanitization system as a low or no maintenance

solution to your spa maintenance program.

• Use a sanitizer which is not designed for spas.

• Use swimming pool (muriatic) acid to lower pH.

• Use household bleach (liquid sodium hypochlorite).

• Broadcast or sprinkle the chemicals onto the water surface. This

method may cause chemically-induced spa surface blistering (chemical

abuse).

VACATION WATER CARE

INSTRUCTIONS

If you plan to be away from home, follow these instructions to ensure

that the water quality of your spa is maintained:

SHORT TIME PERIODS (3-5 DAYS):

1. Adjust the pH by following the instructions outlined in the Water Quality

and Maintenance section.

2. Sanitize the water by following the shock procedures also listed in the

Water Quality and Maintenance section.

3. Lock your cover in place using the coverlocks.

4. Upon your return, sanitize the water by following the shock procedures,

and balance the pH.

5. If ACE is installed, please refer to Tips section, vacation or limited use

in the ACE Owner's Manual.

LONG TIME PERIODS (5-14 DAYS):

Prior to leaving:

1. At least one day before you leave, set the temperature to its lowest

level. This setting should represent an approximate water temperature

of 80°F (27°C)

IMPORTANT: Spa water oxidizers such as sodium dichlor (chlorine)

maintain their level of effectiveness substantially longer in warm water

80°F

(27°C)

than in hot water 101°F to 104°F (38°C - 40°C).

2. Adjust the pH as required. Sanitize the water by following the shock

procedures.

Upon your return:

3. Sanitize the water by following the shock procedures. Return the set

temperature to its original setting. The spa water will be safe for you to

use once the Free Available Chlorine residual level has dropped below

5.0 ppm.

IMPORTANT: If you will not be using your spa for an extended period

of time (in excess of 14 days) and an outside maintenance service

(or neighbor) is not available to assist with the water maintenance,

draining or winterizing of the spa is recommended. Spas equipped

with our FRESHWATER III ozone system can extend this to 4 weeks.

The FRESHWATER III ozone system does not guard against possible

freezing damage, however.

SUPPLEMENTAL WATER MAINTENANCE

Proper water sanitation and mineral balance (pH control) are absolutely

essential for a complete spa water maintenance program. Here are two

other popular water additives that are optional:

Mineral Deposit Inhibitors

As water evaporates from your spa and new water is added, the amount

of dissolved minerals will increase. (Minimize evaporation by keeping

the cover on the spa whenever possible.) The spa water may eventually

become “hard” (Calcium Hardness too high) enough to damage the

heater by calcifying its surface. Proper pH control can minimize this.

Normal soap build-up will require water replacement regularly enough

that mineral deposits normally are not a problem.

Occasionally, high iron or copper content in the water may produce

green or brown stains on the spa. A stain and scale inhibitor may help to

reduce these metals.

IMPORTANT: Well water may contain high concentrations of minerals.

The use of a low water volume, extra-fine pore water filter (in-line pre-

filter such as the CLEAN SCREEN pre-filter) will help to remove many of

the larger particles during the filling of the spa. In-line pre-filters can be

purchased at your local HOT SPRING dealer.

Foam Inhibitors

Spa water requires changing due to the buildup of soap in the water.

Typically, soap will cause the spa water to foam when the jets are used.

Soap is introduced into the spa water from two sources: users’ bodies,

which retain a soap residual after showering, and swimming apparel,

which retains soap after washing.

Foam inhibitors can suppress foam, but cannot remove soap from the

water. Soap is very difficult to remove from the water because soap is

not oxidized by any chemical added to the spa. Only ozone can oxidize

soap.

Hot Spring SOVEREIGN - II Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info