Bedienungsanleitung Hot Spring SOVEREIGN - II (Seite 39 von 48) (Englisch)

624652

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Page 36

Electrical Requirements

bottom of the equipment compartment door. For your safety, when

the electrician is installing the 20 amp single electrical outlet and

waterproof cover, the outlet should be no closer than 5 feet (1.5

meters) and no farther than 10 feet from the spa [reference National

Electrical Code 680-6a(1) and 680-41a].

The Ground Fault Circuit Interrupter (GFCI) is located at the end of

the power cord. This device is for your protection. It is very important

to protect it from rain and other moisture. Test once a month, with the

plug connected to the power supply,

1. Push the “TEST” button on the GFCI breaker. The spa should stop

operating and the GFCI power indicator will go out.

2. Wait 30 seconds, then push the “RESET” button. Power will be

restored to the spa and the GFCI power indicator will turn on.

If the GFCI fails to operate in this manner, your spa may have an

electrical malfunction,

and you may be risking

electrical shock. Turn

off all circuits and

do not use the spa

until the problem has

been corrected by an

authorized service

agent.

WARNING:

Removal of the GFCI

from the spa’s power

cord will result in an

unsafe spa and will void

the spa’s warranty.

IMPORTANT: Should

you ever find the need

to move or relocate

your HOT SPRING

spa, it is essential that

you understand and apply these installation requirements. Your HOT

SPRING spa has been carefully engineered to provide maximum

safety against electric shock. Remember, connecting the spa to an

improperly wired circuit will negate many of its safety features.

ADVANTAGE TO HAVING

YOUR SPA CONVERTED

• In the 115 volt configuration, either the heater, or the jet pump can

operate, but they can’t work at the same time. In a 115 volt system,

as long as the jet pump is activated, the heater will not turn on. On

the other hand, when the spa is converted to operate in the 230 volt

configuration, the heater and jet pump can operate simultaneously.

• The heater will operate at 1500 watts when the spa is configured as

a 115 volt cord-and-plug connected model, and at 6000 watts when

the spa is configured as a 230 volt converted model heating your spa

water faster.

115/230 VOLT CONVERTIBLE MODEL

The PRODIGY and JETSETTER models can be converted to 230

volt operation with the addition of a subpanel and a control box wiring

change. Consult your dealer before attempting to convert from 115 volt

operation to 230 volt operation. Any damage to the spa from improper

conversion is not covered under the warranty.

230 VOLT (PRODIGY & JETSETTER)

CONVERSION INSTRUCTIONS

HOT SPRING spas must be wired in accordance with all applicable

local electrical codes. All electrical work should be done by an

experienced, licensed electrician. We recommend the use of

appropriate electrical conduit, fittings, and wire for all circuits.

Refer to the following instructions to convert from 115 volt to 230 volt

IMPORTANT: Converting the spa to 230 volt operation will require both

an authorized HOT SPRING service agent and a qualified electrician.

Required Part: A Subpanel (230 volt Convertable) available from your

HOT SPRING dealer.

1. Disconnect the power cord from the house receptacle.

2. Open the equipment compartment door.

3. Remove the screws on the front of the spa control box.

4. Open the control box cover.

5. Identify Terminal block located in the lower left-hand corner inside the

control box.

6. Refer to illustration, Step 1. Remove the 2 pin jumper attached to

terminals

4 and 5.

7. Refer to illustration, Step 1. Remove the wire jumper from terminals 2,

and 6.

8. Refer to illustration, Step 2. Remove the power cord wires from 5, 7

and GRD (not illustrated).

9. Unscrew the power cord strain relief and remove the power cord from

the access hole in the control box.

WARNING: Do not allow pliers to contact any electronic components

inside the control box.

Converting from 115 volts to 230 volts changes the voltage supplied

to the

heater from 115-volts to 230 volts. The jet pump will continue to

operate at 115 volts.

Have your licensed electrician wire subpanel from a 50A Main Service,

then from subpanel into the spa's control box using the following illustration

or use the wire diagram on the inside of the control box lid.

IMPORTANT: The subpanel must be placed in sight of the spa, at a

minimum distance of 5 feet away.

WIRING CONNECTIONS

IMPORTANT: Fill the spa with water before turning on the power

• Once your spa has been filled with water, turn it on and test all the

circuit breakers.

Each breaker should be tested prior to each use. Here’s how:

1. Push the “TEST” button on each GFCI breaker, and observe it click

off.

2. Wait 30 seconds, then push the breaker switch to the OFF (down)

position (to ensure that it has completely disengaged), then push the

breaker switch to the ON (up) position. If you don't wait 30 seconds,

the spa’s power indicator may continue to blink – try again.

If any of the GFCI breakers fails to operate in this manner, your spa

may have an electrical malfunction, and you may be risking electrical

shock. Turn off all circuits and do not use the spa until the problem has

been corrected by an authorized service agent.

IMPORTANT: Service Technician must reconfigure spa using the soft

jumpers to allow spa heater to run concurrent with jet pump.

Remove the Terminal Block Power Jumper

using needlenose pliers From terminal 4-5.

Remove wire jumper from 2 & 6.

Remove the three power cord wires from

terminal block 5,7 and GRD. Leave Terminal

Block Power Jumper 6-7 in place.

Step 1

Step 2

Hot Spring SOVEREIGN - II Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info