Bedienungsanleitung Hotpoint-Ariston AQC9 4F7 (Seite 12 von 20) (Englisch)

665355

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The Controls

• Programme knob

! Warning, if after pressing the start button the programme

knob position is changed, the new position will NOT change

the programme selected.

To change programme press Start/Pause Button to pause

the programme, the light flashes Amber, select new programme

and any option, the light will then flash green. Press the Start/

Pause Button and the new programme will start.

• Option Buttons/ Lights

These buttons are used to customise the selected

programme to your requirements. Not all options are

available for all programmes (see Start and Programmes).

If an option is not available and you press the button, the

buzzer will beep three times. If the option is available the

option light next to the button lights to confirm the selection.

• ECO Light

This light is illuminated when you select programme options

that will use less energy than the default setting. Examples

are if you choose an Automatic or sensing programme or

use a timed dry setting less than the default time. This light

does not indicate that the optimum setting for energy use

has been selected; it only shows you that your selected

options will use less energy.

• Progress ( Drying, Cool tumble, ) Lights

The Progress lights show you the status of the programme. At

each stage of the programme the corresponding light turns on.

• Delay Start

The start of some programmes (see Start and Programmes)

can be delayed for up to 24 hours (see The Display).

Ensure the water bottle is emptied and the filter is cleaned

before setting a delayed start.

• Less Fluff

By reducing the mechanical action during the final drying

stage the amount of lint and fluff produced is substantially

reduced protecting the fibres of your garments. Note: For

Shirts programme, if you have selected Low Heat option,

this option is not available.

• Sound

A buzzer sounds at the end of the drying cycle to signal that

the programme has ended and the garments are ready to

be removed. Note: If you have selected Crease Care option,

this option is not available.

• Crease Care

When a delayed start and this option have been selected the

clothes are tumbled occasionally during the delayed period

to help prevent creases developing.

After end of the drying and cool tumble cycles, the clothes

are occasionally tumbled to help prevent creases developing,

should you not be available to remove the load immediately

after the programme is complete. The light is on during

this phase after end of the cycle and the start/pause light

flashes amber. flashes amber. Note: If you have selected the

Sound option, this option is not available.

• High Heat

When a drying time is selected, pressing this button sets

a high heat drying and the indicator light above the button

lights up.

• Empty Water Clean Filter Light “h2o”

(If you have plumbed your dryer to a drain the light can be

ignored for the water bottle, as there is no need to empty the

water container). When is on (not flashing) it reminds you to

empty the water container. If the water container fills during a

programme, the heater turns off and the dryer does a period

of Cool Tumble then the light flashes and the buzzer sounds.

You must empty the container and restart the dryer or the

clothes will not dry. After re-starting the dryer the light will take

a few seconds to go out. To avoid this always empty the water

container each time you use the dryer (see Maintenance).

! Please note that you ALWAYS have to clean the filter even if

you have plumbed your dryer to a drain.

• Door Opening

Opening the door (or pressing the Start/Pause Button) during a

programme will stop the dryer and have the following effects.

Note: The Start/Pause Light flashes Amber during the Post

Care phase of a programme.

• During a delay phase the delay will continue to count

down. The start button must be pressed to resume the

delay programme. One of the delay lights will flash to

show the current delay setting.

• The start button must be pressed to resume the

programme. The progress lights will change to show the

current status and the Start/Pause light will stop flashing

and turn green.

• During the post creasecare phase of a drying program,

the Programme will finish. Pressing the Start/Pause

button will restart a new program at the beginning.

• Changing the Programmes knob will select a new

programme and the Start/Pause Light will flash green.

You can use this to select the “Refresh” programme to

cool the clothes if you find them dry enough. Pressing the

start/pause button to begin new Programme.

• Heat Pump Protection System

The heat pump sytem has a compressor protection

feature, that operates if you open the door or there is a

power disruption or you turn off the dryer. This system

will prevent the heat pump compressor from starting for

5 minutes after the door is closed and the programme

started.

• Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, plug in the machine,

press and hold the ON/OFF button until the dryer

reactivates, then press Start/Pause button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston AQC9 4F7 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info