Bedienungsanleitung Hotpoint-Ariston AQC9 BF7 (Seite 16 von 20) (Englisch)

665357

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Maintenance and Care

Switching off the electricity

! Unplug the dryer when not using it, when cleaning it, and

during maintenance activities.

Clean the filter after each cycle

The filter is an important part of your dryer: it accumulates

lint and fluff that is formed while drying.

When finished drying, clean the filter by rinsing it under

running water or with your vacuum cleaner. Should the

filter become clogged up, the airflow inside the dryer will be

seriously compromised: drying times lengthen and you will

consume more energy. It may also damage your dryer.

The filter is found in front of the dryer trim (see diagram).

Removing the filter:

1. Pull the plastic grip of the

filter upwards (see diagram).

2. Open the filter by

depressing the clip.

3. Clean the lint from the

inside of the filter, and

replace it correctly. Ensure

the filter is fully located flush

into the tumble dryer trim.

! Do not use dryer without replacing the filter.

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless steel

drum, this may be caused by a combination of water

and, or cleaning agents such as fabric conditioner from

the wash. This coloured film will not affect the dryer

performance.

Empty the Water Container after each cycle

Pull the container out of the dryer and empty it into a sink or

other suitable drain. Replace container securely.

Always check and empty the container before you start a new

drying programme.

Cleaning the Condenser Unit

• Periodically (every month) remove Condenser unit and

clean any build up of fluff from between the plates by

rinsing it under the tap with cold water. This should be

done with cold water from the rear of the condenser.

To remove condenser :

1. Unplug the dryer and open the door.

2. Pull open the condenser cover (see diagram), release

the three catches by turning 90° counter clockwise then pull

on the grip and remove from dryer.

3. Clean the surface of the seals and replace with the

arrows pointing upwards making sure that the catches

have been secured.

Cleaning the dryer

• External parts in metal or plastic and rubber parts can

be cleaned with a damp cloth.

• Periodically (every 6 months) vacuum the front Air intake

grille, to remove any build up of fluff, lint or dust. Also to

remove accumulation of fluff from the front of condenser and

filter areas, clean occasionally with a vacuum cleaner.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which do not

need lubrication.

! Have your dryer checked regularly by authorized technicians

to ensure electrical and mechanical safety (see Service).

Water Contaniner

Condenser

Unit

Condenser Cover

Catches

Filter

Handle

Air Intake

Tap

Rear

Front

Condenser

Unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston AQC9 BF7 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info