Bedienungsanleitung Hotpoint-Ariston AQD970F 69 EU (Seite 6 von 48) (Englisch, Italienisch, Portugiesisch, Spanisch)

479290

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WARNING: before you use the wasdher-dryer for the first

time, run a wash cycle with detergent and no laundry, using

the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the button.

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the button will then

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

2. LOAD THE LAUNDRY. Open the porthole door. Load

the laundry, making sure you do not exceed the maximum

load value indicated in the table of wash cycles on the

following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Description of

the machine”.

4. CLOSE THE PORTHOLE DOOR.

5. SELECT THE PROGRAMME. Turn the WASH CYCLE

SELECTOR KNOB right or left, until you have selected the

desired wash cycle. A temperature and spin speed is set

for each wash cycle; these may be adjusted.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons on the control panel:

Modify the temperature.

The machine automatically displays the maximum

temperature values set for the selected cycle, or the most

recently-used settings if they are compatible with the

selected cycle. The temperature can be decreased by

pressing the button, until the cold wash ( ) setting

is reached. If this button is pressed again, the maximum

values are restored.

! Exception: if the programme is selected, the

temperature can be increased up to a value of 90°C.

Setting the drying cycle.

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the drying

time, until the cycle is excluded completely ( ). If this

button is pressed again, the maximum values are restored.

Drying may be set as follows:

A - Based on a set time period: between 20 and 180 minutes.

B- Based on the desired laundry dryness level:

Iron “L1”: suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

Hanger “L2”: ideal for clothes which do not need to be

dried fully.

Cupboard “L3”: suitable for laundry which can be put

back in a cupboard without being ironed.

Extra “L4”: suitable for garments which need to be dried

completely, such as sponges and bathrobes.

If your laundry load to be washed and dried is much

greater than the maximum stated load, perform the

wash cycle, and when the cycle is complete, divide the

garments into groups and put some of them back in

the drum. At this point, follow the instructions provided

for a “Drying only” cycle. Repeat this procedure for the

remainder of the load.

A cooling-down period is always added to the end of each

drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle

( - - ) in accordance with the type of fabric. The

desired drying level or time may also be set using the

DRYING button .

Set a delayed start.

Press the button until you have reached the desired delay

time. During the setting process, the delay time is shown

on the display and the symbol flashes. After selecting

a delayed start time, the fixed symbol and the cycle

duration will appear on the display. Press the button once

to display the selected delay time. To remove the delayed

start option, press the button until the display shows the

text OFF; the symbol will disappear.

! Once the START/PAUSE button has been pressed, the

time delay may only be decreased.

Modify the cycle settings.

Press the OPTION buttons to customise the wash cycle in

accordance with your own requirements.

 •Pressthebuttontoactivatetheoption;the

corresponding indicator light will switch on.

 •Pressthebuttonagaintodisabletheoption;the

indicator light will switch off.

! If the selected option is not compatible with the selected

wash cycle, this incompatibility will be signalled by the

flashing of the indicator light and a sound alert

(3 beeps); the option will not be activated.

! If the selected option is not compatible with another

option that has been selected previously, the indicator light

corresponding to the first option selected will flash and

only the second option will be activated; the indicator light

corresponding to the button will remain lit in a constant

manner.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit in a

fixed manner and the porthole door locks (the LOCK

indicator light illuminates). The icons corresponding to the

wash cycle phases will light up during the cycle to indicate

which phase is currently in progress. To change a wash

cycle once it has already started, pause the wasdher-dryer

by pressing the START/PAUSE button; then select the

desired cycle and press the START/PAUSE button again.

To open the door during a wash cycle, press the START/

PAUSE button; if the LOCK indicator light is switched

off you may open the door. Press the START/PAUSE

button again to restart the wash cycle from the point at

which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light is

flashing, press the button to end the cycle. Open the door,

unload the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button until the cycle stops and the

machine switches off.

How to run a wash cycle or a

drying cycle

Hotpoint-Ariston AQD970F 69 EU Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotpoint-Ariston AQD970F 69 EU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info