Bedienungsanleitung Hotpoint-Ariston AQUALTIS AQS82D 29 (Seite 2 von 48) (Englisch, Französisch, Italienisch)

570823

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Installation

! This instruction manual should be kept in a

safe place for future reference. If the washing

machine is sold, given away or moved, please

ensure the manual is kept with the machine,

so that the new owner may benefit from the

advice contained within it.

! Read these instructions carefully: they

contain vital information relating to the safe

installation and operation of the appliance.

! Inside the pack containing this manual, you

will also find the guarantee and all the details

necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging

from the washing machine, make sure it has not

been damaged during transportation. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4

protective screws

(used during

transportation) and

the corresponding

spacer, located on

the rear part of the

appliance (see figure).

3. Close off the holes using the plastic plugs

supplied in the pack.

4. Keep all the parts in a safe place; they will

be needed again if the washing machine is

moved to another location, to prevent the

inside of the appliance being damaged.

! Packaging materials should not be used as

toys for children.

Levelling

1. Place the washing machine on a flat sturdy

floor, without resting it up against walls or

cabinets.

2. If the floor is

uneven, the front feet

of the machine may

be adjusted until it

reaches a horizontal

position (the angle of

inclination must not

exceed 2 degrees).

! If the appliance is levelled correctly, it will

be more stable and much less likely to cause

vibrations and noise while it is operating,

particularly during the spin cycle.

! If it is placed on carpet or a rug, adjust the

feet in such a way as to allow a sufficient

ventilation space underneath the washing

machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water

supply, run the water until it is perfectly clear.

1. Connect the inlet

hose to the machine

by screwing it onto

the cold water inlet of

the appliance, which

is situated on the top

right-hand side of

the rear part of the

appliance (see figure).

2. Insert seal A into

the end of the inlet

hose and screw the

latter onto a cold

water tap with a 3/4

gas threaded mouth

(see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical data table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston AQUALTIS AQS82D 29 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info