Bedienungsanleitung Hotpoint-Ariston AQXGF 149 (Seite 2 von 72) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

69800

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Installation

 Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away

or moved, please ensure the manual remains with the

machine so that the new owner may benefit from the

advice contained within it.

 Please read this instruction manual carefully it

contains important information regarding the safe

installation, use and maintenance of the appliance.

 You will find the guarantee and other details relating to

the installation process in the bag containing this booklet.

Unpacking and levelling

Unpacking

1. Once the washing machine has been removed

from the packaging, check that it has not been

damaged during transportation.

If it has been damaged, contact the retailer and do

not proceed any further with the installation process.

2. Remove the 4 transit

bolts used during

transportation and the

corresponding spacers

on the back of the

machine (see figure).

3. Having removed the 4 bolts use the 4 plastic

blanking plates to cover the 4 holes.

4. Keep all the pieces; if the washing machine is

transported in future, the transit bolts and spacers will

have to be replaced in order to avoid damaging the

inside of the machine.

 Packaging materials should not be used as toys by children.

Levelling

1. Position the washing machine on a level and sturdy

floor, without resting it against walls or cabinets.

2. If the floor is uneven,

the feet of the appliance

may be adjusted until it

reaches a perfectly

horizontal position (the

angle of inclination must

not exceed 2 degrees).

 If the appliance is levelled correctly it will be more

stable and much less likely to cause vibrations and

noise during the spin cycle.

 If positioned on a fitted carpet or a rug, adjust the

feet in such a way as to allow room for air to circulate

and provide ventilation beneath the washing machine.

Connecting the cold water and

electricity supplies

Connecting the water inlet hose

 Before connecting the inlet hose to the cold water supply,

allow the water to flow from the tap until it runs clear.

1. Connect the end of

the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

2. Place the seal A

(provided in the bag) on

the end of the inlet hose

and screw it to a cold

water tap with a 3/4 gas

threaded connection (see

figure).

3. Make sure there are no kinks or bends in the inlet hose.

 The water pressure at the tap must fall within the values

indicated in the Technical data table (see next page).

 If the water inlet hose is not long enough, contact a

specialist store or an authorised technician.

 Always use the new water inlet hoses supplied with

the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston AQXGF 149 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info