Bedienungsanleitung Hotpoint-Ariston ETM 16110 T (Seite 7 von 32) (Englisch, Französisch, Portugiesisch, Spanisch)

511505

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Installation

! Before placing your new appliance into operation please read

these operating instructions carefully. They contain important

information for safe use, for installation and for care of the

appliance.

! Please keep these operating instructions for future reference. Pass

them on to possible new owners of the appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to operate

correctly and save energy.

3. Leave a space of at least 10 cm between the top part of the

appliance and any furniture above it, and at least 5 cm between

the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat (direct

sunlight, electric stove, etc.).

5. In order to maintain the correct distance between the appliance

and the wall behind it, fit the spacers supplied in the installation kit,

following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, adjust the refrigerator by

tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it vertically

and wait at least 3 hours before connecting it to the electricity mains.

Before inserting the plug into the electrical socket ensure the

following:

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance,

which is indicated on the data plate located on the bottom left side

of the fridge (e.g. 150 W).

• The voltage must be in the range between the values indicated on

the data plate located on the bottom left side (e.g. 220-240V).

• The socket is compatible with the plug of the appliance. If the

socket is incompatible with the plug, ask an authorised technician

to replace it (

see Assistance

). Do not use extension cords or

multiple sockets.

! Once the appliance has been installed, the power supply cable and

the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised

technicians only (see Assistance).

! The manufacturer declines any liability should these safety

measures not be observed.

Start-up and use

Starting the appliance

! Before starting the appliance, follow the installation

instructions (

see Installation

! Before connecting the appliance, clean the compartments and

accessories well with lukewarm water and bicarbonate.

1. Insert the plug into the socket and ensure that the internal light

illuminates.

2. Turn the TEMPERATURE ADJUSTMENT knob to an average

value. After a few hours you will be able to put food in the

refrigerator.

Setting the temperature

The temperature inside the refrigerator compartment automatically

adjusts itself according to the position of the TEMPERATURE

ADJUSTMENT knob.

1 = warmest 5 = coldest

We recommend, however, a medium position.

The cooling section of the refrigerator is located inside the back wall

of the refrigerator compartment for increased space and improved

aesthetics. During operation, the back wall will be covered in frost or

water droplets depending on whether the compressor is operating or

paused. Do not worry, the refrigerator is functioning normally.

If the TEMPERATURE ADJUSTMENT knob has been set on high

values with large quantities of food and with a high ambient

temperature, the appliance can operate continuously, resulting in

excessive frost formation and excessive energy consumption:

compensate for this by shifting the knob towards lower values

(defrosting will occur automatically). In static appliances, the air

circulates in a natural way: the colder air tends to move downwards

as it is heavier. The food should be stored as follows:

Food

Arrangement inside the

refrigerator

Fresh fish and meat Above the fruit and vegetable bins

Fresh cheese Above the fruit and vegetable bins

Cooked food On any shelf

Salami, loaves of bread,

chocolate

On any shelf

Fruit and vegetables

In the fruit and vegetable

compartment bins

Eggs On the shelf provided

Butter and margarine On the shelf provided

Bottles, drinks, milk On the shelves provided

PURE WIND *

It is recognizable due to the presence of the mechanism on the top

part of the refrigerator compartment (

see diagram

Pure Wind maximises air circulation, improving the efficiency of the

evaporator and helping to achieve the optimal temperature inside the

refrigerator as quickly as possible each time it has been opened.

The blown air (A) is cooled when it comes into contact with the cold

wall, whereas the hotter air (B) is sucked up (

see diagram

Using the refrigerator to its full potential

• Place only cold or lukewarm foods in the compartment, not hot

foods (

see Precautions and tips

• Remember that cooked foods do not last longer than raw foods.

• Do not store liquids in open containers. They will increase

humidity in the refrigerator and cause condensation to form.

SHELVES: with or without grill.

Due to the special guides the shelves are removable and the height

is adjustable (

see diagram

), allowing easy storage of large

containers and food. Height can be adjusted without complete

removal of the shelf.

* Varies by number and/or position, available only on certain

models.

Hotpoint-Ariston ETM 16110 T Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info