Bedienungsanleitung Hotpoint-Ariston FTCL 87 (Seite 13 von 20) (Englisch)

665337

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Start and Programmes

●

PROGRAMMES knob

! Warning, if after pressing the start button, the

programmes knob position is changed, the new position

will NOT change the programme selected.

To change a selected programme, press the

Start/Pause button , the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will

then flash green. Press the Start/Pause button

again and the new programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. Not all options are

available for all programmes (see Start and

Programmes). If an option is not available and you

press the button, the buzzer will beep three times.

If the option is available the option light next to the

button lights to confirm the selection.

Progress ( Drying, Cool Tumble, END) /

Delay (3hr 6hr 9hr) Lights

When the light next to the delay button is on, these lights

flash to indicate the delay time selected. During other

programmes they indicate the progress of the dryer,

each one comes on as the corresponding phase starts.

Delay Timer (Delay)

The start of some programmes (see Start and

Programmes) can be delayed for up to 9 hours in 3hr

steps. Ensure the water bottle is emptied before setting

a delayed start.

When a delayed start is in progress the light next to the

delay button will be on and the selected delay period

light will flash (after the start button has been pressed).

To set a delayed start, press the Delay Timer button,

and the light next to the button will come on together

with the 3hr delay light. Pressing the button again will

advance the delay setting to 6hr, the 3hr light goes

out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated

by the corresponding light. If the 9hr light is on,

pressing the button again will cancel the delay.

Holding in the On/Off button will also cancel.

Extra Care

This Anti-Ageing function for Cottons helps to maintain the

brightness of your laundry for a long time, thanks to the

correct drum rotation (reduced in the last part of the cycle)

and the correct temperature.

Note: It cannot be used with the ‘Extra Dry’, ‘Cupboard Dry’

and ‘Light Dry’ dryness levels.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during

the delayed period to help prevent creases developing.

The post-care option occasionally tumbles the clothes

after the end of the drying and cool tumble cycles to

prevent creases developing, should you not be available

to remove the load immediately the programme is

complete. The End light is on during this phase.

Note: The Start/Pause light flashes Amber during this

phase.

Selecting this option enables both the pre and post care

functions if appropriate.

The Controls

High Heat

Press this button and a high heat setting is selected and

the light next to the button comes on. If the light

alongside the button is on then pressing the button

selects a low heat setting and the light goes out.

Not all programmes allow you to change this setting.

Empty Water Light / Container

(If you have plumbed your dryer to a drain this light

can be ignored, as there is no need to empty the water

container).

When this light is on (not flashing) it reminds you to

empty the water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble then the light flashes and the buzzer sounds.

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer, the light will take a few seconds to go out.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door (or pressing the Start/Pause button)

during a programme will stop the dryer and have the

following effects:

Note: The Start/Pause light flashes Amber during the

Post Care phase of a programme.

●

The Start/Pause light flashes Amber.

●

During a delay phase the delay will continue to

count down. The Start/Pause button must be

pressed to resume the delay programme.

One of the delay lights will flash to show the

current delay setting.

●

The Start/Pause button must be pressed to

resume the programme. The progress lights will

change to show the current status and the

Start/Pause light will stop flashing and turn green.

●

During the Post Creasecare phase of a drying

programme, the programme will finish. Pressing

the Start/Pause button will re-start a new

programme at the beginning.

●

Changing the programmes knob will select a new

programme and the Start/Pause light will flash

green. You can use this to select the Refresh

programme to cool the clothes, if you find them

dry enough. Press the Start/Pause button to begin

a new programme.

●

Heat Pump Protection System

The heat pump system has a compressor protection

feature that operates if you open the door or there is a

power disruption or if you turn off the dryer. This system

will prevent the heat pump compressor from starting for 5

minutes after the door is closed and the programme is

started.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press and hold the

ON/OFF button until the dryer reactivates, then press the

Start/Pause button.

Hotpoint-Ariston FTCL 87 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info