Bedienungsanleitung Hotpoint-Ariston HV7L 1451 (Seite 13 von 16) (Englisch)

665266

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem

The machine does not switch on.

The wash cycle does not start.

The machine does not fill with

water or the indicator light for

the first wash cycle stage flashes

rapidly.

The machine continuously fills

with water and continually drains

away or Water left in the dru or

Stuck on wash.

The machine does not drain or

spin.

The machine does not heat or

poor wash results.

The programme takes too long.

The machine vibrates a lot during

the spin cycle.

Possible causes/Solution:

• The appliance is not plugged into the socket fully, or not enough to

make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

• The door is not closed properly.

• The ‘ON/OFF’ button has not been pressed.

• The ‘START/PAUSE’ button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The ‘START/PAUSE’ button has not been pressed.

• The top of the drain hose is too low - It must be fitted at a height

between 65 and 100 cm from the floor.

• The drain hose is connected incorrectly to the sink trap allowing

water to run into the machine, the drain hose must be positioned

higher than the bottom of the sink to prevent water flowing down the

drain hose.

• The end of the drain hose has been pushed too far down the standpipe,

the ‘U’ bracket should be fitted 100 mm from the end of the drain hose.

• The Pump filter is blocked.

• The drain hose is kinked.

• New Installation - The blanking cap or spigot has not been removed

if connected under a sink.

• The drain hose or sink trap is blocked.

• The wash cycle does not include draining, some wash cycles require

the drain phase to be started manually.

• The REDUCED CREASES function button has been activated. To complete

the wash cycle, press the START/PAUSE button.

• The ‘Spin Speed’ selector knob is in the position.

• The ‘Temperature’ selector knob is in the position.

• Programme times will vary due to water pressure, the incoming

water temperature and if the wash load goes out of balance.

This will increase the programme times accordingly (see ‘ The

machine wont spin properly’ below).

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but

at a lower speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston HV7L 1451 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info