Bedienungsanleitung Hotpoint-Ariston lff 8246 x fr ha (Seite 21 von 24) (Englisch, Französisch)

127648

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite



Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard. Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

 When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making

sure it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry

cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Use a screwdriver

to turn the dosage adjuster (F) to one of the 6 pre-set

positions (the default position is set to 4):

 If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

 If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set the

adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Switch on the machine by pressing the ON/OFF button.

- Press the P button and hold for approximately 5 seconds;

two short beeps will sound and the indicator light

corresponding to the set degree of hardness will flash slowly

on the control panel (The default water softener setting is level

3).

- Press the P button repeatedly until the desired hardness

level has been reached (1-2-3-4-5

* see Water hardness

table).

E.g. hardness level 1 (wash cycle indicator light 1 flashing),

hardness level 2 (wash cycle indicator light 1 illuminated, wash

cycle indicator light 2 flashing), hardness level 3 (wash cycle

indicator lights 1 and 2 illuminated, wash cycle indicator light 3

flashing, etc. etc.), up to a maximum of 5 levels.

- To exit the function, wait approximately 30 seconds or press

another option button, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees - mmol/l = millimoles per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty. Refined

salt removes limescale from the water, thus avoiding the

formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description) and should be filled:

 When the green float* cannot be seen by simply looking at the

cap of the salt dispenser.

 When the LOW SALT* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew

the container cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel* (see figure) and

fill the salt container right up to its edge

(this should hold approximately 1 kg); it

is not unusual for a little water to leak

out.

4. Remove the funnel* and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it

on, the head facing downwards so as to let the water flow out of

the four cracks which are arranged in a star shape on the lower

part of the cap. (Salt cap with green float

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash cycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

°dH °fH mmol/l level

0 6 0 10 0 1 1

6 11 11 20 1.1 2 2

12 17 21 30 2.1 3 3

17 34 31 60 3.1 6 4

34 50 61 90 6.1 9

For values between 0°f and 10°f, we do not

recommend the use of salt.

* this setting may cause a slight increase in the

duration of the cycle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston lff 8246 x fr ha Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info