Bedienungsanleitung Hotpoint-Ariston LFF 8B5 (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

593393

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table salt or industrial salt, or washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt, especially

if you live in an area where the water is hard or very hard.

Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW SALT

* and

LOW RINSE AID

* indicator lights remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs

off surfaces more readily and therefore does not leave streaks or

marks.

The rinse aid dispenser should be filled:

• When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning the

lid (G) in an anticlockwise direction.

2. Pour in the rinse aid, making sure it

does not overflow from the dispenser.

If this happens, clean the spill

immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Use a screwdriver to

turn the dosage adjuster (F) to one of the 6 pre-set positions (the

default position is set to 4):

• If there are streaks on the crockery, set the adjustment device

to a lower number (1-3).

• If drops of water remain on the crockery or if there are limescale

marks present after the cycle has finished, set the adjuster to a

higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash the

crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the water

hardness level in your area. This information can be obtained

from the organisation which supplies your household with water.

The water hardness adjustment procedure may vary

depending on the dishwasher model purchased.

- Switch on the appliance by pressing the ON/OFF button.

- Press and hold the P button for a few seconds; after a short

beep sounds, the water hardness setting will appear on the

display and the Start/Pause button will begin to flash (the default

water softening system setting is level

3).

- Press the P button repeatedly until the desired hardness level

has been reached (1-2-3-4-5

see Water hardness table

). The

selected water hardness value will appear on the display.

E.g.: hardness setting 1 ("1" appears on the display);

hardness setting 2 ("2" appears on the display);

hardness setting 3 ("3" appears on the display); etc., etc. up to a

maximum of level 5.

To exit the function, wait a few seconds or press one of the

option buttons

*, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees - mmol/l = millimoles per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash cycle,

make sure that the dispenser is never empty. Refined salt removes

limescale from the water, thus avoiding the formation of deposits

on crockery.

The salt dispenser is located in the lower part of the dishwasher

(

see Description

) and should be filled:

• When the green float

* cannot be seen by simply looking at the

cap of the salt dispenser.

• When the LOW SALT* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. The first time you do this: fill the water tank

right up to its edge.

3. Position the funnel

* (

see figure)

and fill

the salt container right up to its edge (this

should hold approximately 1 kg); it is not unusual for a little water

to leak out.

4. Remove the funnel* and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it on,

the head facing downwards so as to let the water flow out of the

four cracks which are arranged in a star shape on the lower part

of the cap. (the container cap with the green float*)

It is advisable to perform this procedure every time you add

salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash cycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt container

capacity duration

Level

°dH

°fH

mmol/l

months

1 0 - 6 0 - 10 0 - 1

7 months

2 6 - 11 11 - 20 1,1 - 2

5 months

3 12 - 17 21 - 30 2,1 - 3

3 months

4 17 - 34 31 - 60 3,1 - 6

2 months

34 - 50

61 - 90

6,1 - 9

2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt

. *

this setting may cause a slight increase in the

duration of

the cycles.

for 1 wash cycle per day.

Hotpoint-Ariston LFF 8B5 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info