Bedienungsanleitung Hotpoint-Ariston LFTA H214 HX (Seite 18 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

479308

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Start-up and use

Starting the dishwasher

1. Turn the water tap on.

2. Open the door and press the ON/OFF button: you will hear

a short beep and the display and option indicator lights switch

on.

3. Measure out the detergent (see below).

4. Load the racks (see Loading the racks).

5. Select the wash cycle in accordance with the type of

crockery and its soil level (see Table of wash cycles),

pressing the P button.

6. Select the wash options (see adjacent information).

7. Start the wash cycle by shutting the door: a long beep

signals the start of the wash cycle.

8. Two short beeps and one long one indicate the end of the

wash cycle and the wash cycle number flashes on the display.

Open the door, switch off the appliance by pressing the ON/

OFF button, shut off the water tap and unplug the appliance

from the electricity socket.

9. Wait for a few minutes before removing the crockery, in

order to avoid burns. Unload the racks, beginning with the

lower level.

- The machine will switch off automatically

during certain periods of inactivity, in order to

minimise electricity consumption.

AUTO WASH CYCLES*: this model of dishwasher is

equipped with a special sensor which can be used to assess

the level of soiling and automatically select the most efficient

and economic wash cycle accordingly.

The duration of the auto wash cycles may vary due to the

operation of the sensor.

If the crockery is only lightly soiled or if it has been rinsed

with water before being placed in the dishwasher, reduce the

amount of detergent used accordingly.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it has

only just begun: open the door, avoiding the escaping steam,

and press and hold the ON/OFF button; the machine will

switch off with a long beep. Switch the machine back on using

the ON/OFF button and select the new wash cycle and any

options desired; start the cycle by closing the door.

Adding extra crockery

Without switching off the machine, open the door, taking care

to avoid the escaping steam, and place the crockery inside

the dishwasher. Close the door: the cycle starts from the point

at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a

power cut, the cycle stops. It starts again from the point at

which it was interrupted once the door has been shut or once

the electricity supply is restored.

Measuring out the detergent

A good wash result also depends on the correct amount of

detergent being used; exceeding the stated amount does not

result in a more effective wash and increases environmental

pollution.

Only use detergent which has been

specifically designed for dishwashers.

 DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

The use of tablets is only recommended for

models which offer the MULTI-FUNCTIONAL

TABLETS option.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid

liquid and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button

2. Pour in the detergent after

consulting the Table of wash cycles:

 For powder detergent use

compartments A and B.

 For detergent in tablet form: when

the cycle requires 1 tablet, place it in

compartment A and close the cover;

when it requires 2, place the second tablet at the bottom of the

appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

Wash options

If an option is not compatible with the selected was cycle

(see Table of wash cycles), the corresponding LED flashes

rapidly 3 times and 2 short beeps will sound.

Delayed start

It is possible to delay the start time of the cycle by 3, 6 or 9

hours.

1. Press the DELAYED START button: every time it is pressed

a buzzer sounds and the selected period of time is displayed.

2. Select the wash cycle and shut the door: after the beep

sounds, the timer begins counting down.

3. Once this time has elapsed, the indicator light switches off

and the wash cycle begins.

To adjust the delay time and select a smaller period of time,

press the DELAYED START button. To cancel it, press the

button repeatedly until the selected delayed start indicator

light switches off. The wash cycle will start automatically as

soon as the door is shut.

* Only available in selected models.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston LFTA H214 HX Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info