Bedienungsanleitung Hotpoint-Ariston li 485 a c ha (Seite 15 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

127564

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

#

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct

with a minimum diameter of 4 cm. Alternatively, rest it over a

sink or tub; the free end of the hose should not remain

immersed in water.

The special plastic elbow

makes it easier to find the best

layout: fix the elbow to the wall

securely in order to prevent the

outlet hose from moving and

spilling the dirty water.

The part of the hose marked

with the letter A should be

between 40 and 100 cm above

the ground (see figure).

We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket, make sure

that:

 the socket is earthed and complies with current regulations;

 the socket can withstand the maximum load of the appliance,

which is indicated on the data plate located on the inside of

the door (see Description of the appliance);

 the power supply voltage falls within the values indicated on

the data plate on the inside of the door;

 the socket is compatible with the plug of the appliance. If this

is not the case, ask an authorised technician to replace the

plug (see Assistance); do not use extension cables or multiple

sockets.

Once the appliance has been installed, the power supply

cable, the electrical plug and socket should remain accessible.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order

to prevent all potential hazards. (See Assistance)

The cable should not be bent or compressed.

The Company shall not be held responsible for any incidents

that occur if these regulations are not observed.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before

running the first wash cycle, completely fill the salt dispenser

with water and add approximately 2 kg of salt (see Rinse aid

and refined salt). The water may overflow: this is normal and is

not a cause for concern. It is also normal that the LOW SALT

indicator light continues to flash for a few cycles after the salt

has been loaded.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order to

protect it from any condensation that may form.

* Only available in selected models.

Technical data

Dimensions

width 44.5 cm

height 82 cm

depth 57 cm

Capacity

9 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

4.3 psi – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse

See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-2006/95/EEC dated

16/01/2007

(Low Voltage) and subsequent

modifications

-89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent modifications

-97/17/EC (Labelling)

-2002/96/ CE (

Waste

Electrical and Electronic

Equipment WEEE)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston li 485 a c ha Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info