Bedienungsanleitung Hotpoint-Ariston LI 640 A (Seite 9 von 31) (Englisch, Französisch, Spanisch)

71189

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

8 ARISTON DISHWASHER - User Manual

www.aristonappliances.us

The dishwasher won't

start

■ Is the water supply tap turned

on?

■ Is the water supply tap

connected to the hose

properly?

■ Has the water in your home

been cut off?

■ Is the pressure of the water

supply sufficient?

■ Is the hose bent?

■ Is the filter on the water supply

hose blocked?

■ Is the dishwasher door open?

The dishes are not clean.

■ Have you put the right amount

of detergent into the

dispenser?

■ Is the wash cycle suitable for

the dishes you have placed

inside the appliance?

■ Are the filter and microfilter

clean?

■ Can the sprayer arms turn

freely?

The dishwasher won't drain.

■ Is the drain hose bent?

Limescale deposits or a

white film form on the

dishes.

■ Is the lid on the salt container

closed properly?

■ Is the rinse aid dosage

correct?

Error messages.

Your dishwasher is equipped with

a safety system which is able to

detect any operating problems.

These anomalies are reported by

one or two wash cycle indicator

lights "M" will flash rapidly.

Take a note of which lights are

flashing, turn the appliance off

and call for technical assistance.

Tap off alarm

If you have forgotten to turn the

water tap on, your appliance will

remind you of this by sounding a

few short beeps for a few

minutes.Turn the tap on and your

appliance will start up again after

a few minutes.If you were not

home when these beeps are

sounded,the appliance will be

blocked automatically the 2nd

and 3rd light from the right will

flash rapidly.Turn the appliance

off at the ON-OFF button, turn

on the water tap and wait

approximately 20 seconds before

turning the appliance back on; the

selected wash cycle will start up

again.

Clogged filter alarm

If the appliance is blocked and the

2nd and the 4th light from the right

flash rapidly, this means the filter

is clogged by large particles of

food residue. Turn the appliance

off, clean the filter thoroughly and

reposition it in its seat as

illustrated on page 10. Then turn

it back on. The selected wash

cycle will start up again.

Water load solenoid valve

malfunction alarm.

If the 3rd light from the right

flashes rapidly, turn the

dishwasher off and back on

again after one minute. If the

alarm persists, first turn off the

water tap to avoid any flooding

and then cut off the electricity

supply and call for technical

assistance.

You have checked

everything, but the

dishwasher still doesn't

work and the problem

persists?

Call the Ariston Customer Care

(1-888-426-0825) and remember

to mention:

 the type of malfunction

 the model mark (Mod.) and

the serial number (S/N.)

indicated on the rating plate

located on the inner door, to

one side.

Never without salt

Loading the salt.

You can use special water

softening salt or normal rock salt.

The salt container is situated

underneath the lower rack, fill it

up as follows:

1. Pull out the lower rack

completely, unscrew and

remove the container cap

2. Is it the first time you load the

salt? First fill the container up

with water (you won't have to

do this again next time)

3. Put the dishwasher funnel on

the hole and pour in

approximately 70 oz. of salt.

It is normal that some water

comes out of the container.

4. Screw the cap back in place

carefully.

Water in your home

When should I load the

salt?

The salt container should be filled

after about every 30 cycles.

Intelligent salt.

Your dishwasher can adjust its

salt consumption according to the

hardness of the water in your

home. This way, you can optimise

and customise your dishwasher's

salt consumption (not too much,

nor too little).

To adjust salt consumption, do as

follows:

1. Unscrew the salt container

cap

2. There is an arrow on the neck

of the container (see figure):

if necessary, turn the arrow

anti-clockwise from the "-"

setting to the "+" setting.

Select the arrow position

depending on the water

hardness, referring to the table

provided.

Water hardness varies according to where you live. If the water in your home is hard you have the possibility to

add salt in order to soften your water. The softer the water the better will be your washing and drying results.

Water Hardness

Clarke

degrees

°fH mmol/l

Selector

position

Salt

consum-

ption

(Oz/cycle)

Auto-

nomy

(cycles\

70oz.)

0 - 14 0 - 17 0 -1,7 / 0 /

14 - 36 18 - 44 1,8 - 4,4 "-" 0.7 60

36 - 71 45 - 89 4,5 - 8,9 MED 1.4 40

>71 > 89 > 8,9 "+" 2.1 25

NOTE: if you dont find

special water softening

salt you can also use

normal rock salt.

If you have a problem, read this

Your dishwasher may not work or not function properly. In many cases, these are problems which can be solved

without having to call for a technician. Before calling the customer care center, always check the points below.

Troubleshooting

If you dont know your

water hardness ask your

local water supplier.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston LI 640 A Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotpoint-Ariston LI 640 A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info