Bedienungsanleitung Hotpoint-Ariston LLD 8M121 (Seite 28 von 84) (Deutsch, Englisch, Italienisch, Portugiesisch, Spanisch)

570661

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Troubleshooting

Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.

* Only available in selected models.

Problem: Possible causes / Solutions:

The dishwasher does not start or cannot

be controlled.

• Switch off the appliance by pressing the ON/OFF button, switch it back

on after approximately one minute and reset the cycle.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close. • The lock was released. Strongly push the door until a “clacking” noise is

heard.

No water drains from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water drain hose is bent (see Installation.)

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use.)

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of refined salt is low or the dosage setting is not suitable for

the hardness of the water (see Rinse aid and salt.)

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying cycle has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid

and salt.)

• The rinse aid setting is not suitable.

• The crockery is made from non-stick material or plastic.

The crockery is not clean. • The racks are overloaded (see Loading the racks.)

• The crockery has not been arranged well.

• The sprayer arms cannot rotate freely.

• The wash cycle is too gentle (see Wash cycles.)

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use.)

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance.)

• The refined salt level is low (see Rinse aid and salt.)

The dishwasher does not take any

water in - Tap shut-off alarm.

Beeps are heard and H2O is displayed.

F 6 is displayed.

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation.)

• Turn on the tap and the appliance will start after a few minutes.

•

The appliance stopped because no action was taken when the beeps

sounded.

Switch off the machine using the ON/OFF button, turn on the tap and

switch the machine back on after a few seconds by pressing the same

button. Re-program the appliance and restart the wash cycle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston LLD 8M121 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info