Bedienungsanleitung Hotpoint-Ariston LS 240 EU (Seite 17 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

513009

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

You have loaded your dishes and you now have

to set the wash cycle. It takes just one minute

to learn how

Starting the dishwasher

Make sure the

wash cycle has

ended before

removing the

dishes!

Ready, steady, go!

First of all.

Turn on the water tap completely

and press ON-OFF button "A": a

short beep will sound and indicator

light "B" will come on. Now the

appliance is on and ready to be pro-

grammed.

Selecting the wash cycle.

To select a wash cycle, turn knob

"D" clockwise until the reference

notch on the knob corresponds with

the number or symbol for the cy-

cle you wish to set (have a look at

the wash cycle table on page 16).

After a few seconds, you will hear

a short beep: the wash cycle has

begun and it is not advisable to

make any changes at this point.

The dishwasher informs

you.

Your dishwasher is fitted with indi-

cator lights (G) that come on to

show you at which point the wash

cycle is at.

Here are the symbols correspond-

ing to each cycle phase:

Starting from the indicator light on

the left moving towards the one on

the right: pre-wash, wash, rinses,

drying.

At all times, your dishwasher tells

you where it is at.

Modifying a wash cycle in

progress.

But if you have chosen the wrong

cycle, not to worry! You can modify

the wash cycle in progress, if it has

only just started. Turn the knob

anti-clockwise and set it to Reset,

after a few seconds you will hear 4

beeps and indicator light "G" will

go out: this means all the settings

have been cancelled. You are now

free to re-set the correct wash cy-

cle.

You've left out a dish?

Well, it happens to everyone. Inter-

rupt the wash cycle by pressing the

ON-OFF button, insert the dish you

had forgotten and press the ON-

OFF button again. The cycle will

start up from where you interrupted

it.

Finished?

The end of the wash cycle is sig-

nalled by 2 short beeps and a flash-

ing drying phase indicator light. Set

the knob to the Reset position to

clear all settings.

Turn the appliance off by pressing

button "A", thus cutting off the elec-

tricity supply.

Turn off the water tap.

Wait a few minutes before unload-

ing the dishes: they are very hot! If

you wait a little while, they dry

better thanks to the steam.

Empty the lower rack first.

There's been a power fail-

ure? Have you opened the

dishwasher door?

The wash cycle stops and then re-

starts when the electricity comes

back on or when you shut the door.

Everything is under control!

If opening the

door soon after

the end of the

programme,or

during it, stand

away from the

Dishwasher, to

avoid possible

injury from hot

steam.

You can cancel

the wash cycle

in progress, if it

has only just

started.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston LS 240 EU Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info